ADV7190KSTZ Analog Devices Inc, ADV7190KSTZ Datasheet - Page 10

• Manufacturer Part Number: ADV7190KSTZ
• Manufacturer: Analog Devices Inc

Specifications of ADV7190KSTZ

• Number Of Dac's: 6
• Adc/dac Resolution: 10b
• Screening Level: Commercial
• Package Type: LQFP
• Pin Count: 64
• Lead Free Status / RoHS Status: Compliant

ADV7190/ADV7191
Pin
No.
1–16
17, 25, 29,
38, 43, 54,
63
18, 24, 26,
33, 39, 42,
55, 64
19
20
21
22
23
27
28
30
31
32
34
35
36
37
40
41
44
45
46
47
48
49
50
51
52
53, 57–62
56
Mnemonic
P0–P15
V
AGND
HSYNC
VSYNC
BLANK
ALSB
TTXREQ
CLKIN
CLKOUT
SCL
SDA
SCRESET/
RTC/TR
R
COMP 2
DAC F
DAC E
DAC D
DAC C
DAC B
DAC A
COMP 1
V
R
RESET
CSO_HSO
VSO/CLAMP
PAL_NTSC
NC
TTX
AA
SET2
REF
SET1
Input/
Output
I
P
G
I/O
I/O
I/O
I
O
I
O
I
I/O
I
I
O
O
O
O
O
O
O
O
I/O
I
I
O
I/O
I
I
Function
8-Bit or 16-Bit 4:2:2 Multiplexed YCrCb Pixel Port. The LSB of the input data is set up on
Pin P0.
Analog Power Supply (3.3 V to 5 V).
Analog Ground.
HSYNC (Modes 1, 2, and 3) Control Signal. This pin may be configured to be an output
(Master Mode) or an input (Slave Mode) and accept Sync Signals.
VSYNC Control Signal. This pin may be configured as an output (Master Mode) or as an
input (Slave Mode) and accept VSYNC as a Control Signal.
Video Blanking Control Signal. This signal is optional. For further information see Vertical
Blanking Data Insertion and BLANK Input section.
TTL Address Input. This signal sets up the LSB of the MPU address.
Teletext Data Request Output Signal, used to control teletext data transfer.
TTL Clock Input. Requires a stable 27 MHz reference clock for standard operation. Alterna-
tively, a 24.5454 MHz (NTSC) or 29.5 MHz (PAL) can be used for square pixel operation.
Clock Output Pin.
MPU Port Serial Interface Clock Input.
MPU Port Serial Data Input/Output.
Multifunctional Input: Real-Time Control (RTC) Input, Timing Reset Input, Subcarrier Reset
Input.
A 1200 W resistor connected from this pin to ground is used to control full-scale amplitudes
of the Video Signals from DACs D, E, and F.
Compensation Pin for DACs D, E, and F. Connect a 0.1 mF Capacitor from COMP2 to V
S-Video C/V/RED Analog Output. This DAC is capable of providing 4.33 mA output.
S-Video Y/U/BLUE Analog Output. This DAC is capable of providing 4.33 mA output.
Composite/Y/GREEN Analog Output. This DAC is capable of providing 4.33 mA output.
S-Video C/V/RED Analog Output. This DAC is capable of providing 4.33 mA output.
S-Video Y/U/BLUE Analog Output. This DAC is capable of providing 4.33 mA output.
Composite/Y/GREEN Analog Output. This DAC is capable of providing 4.33 mA output.
Compensation Pin for DACs A, B, and C. Connect a 0.1 mF Capacitor from COMP1 to V
Voltage Reference Input for DACs or Voltage Reference Output (1.235 V). An external
V
A 1200 W resistor connected from this pin to ground is used to control full-scale amplitudes
of the Video Signals from DACs A, B, and C.
The input resets the on-chip timing generator and sets the ADV7190/ADV7191 into default
mode. See Appendix 8 for Default Register settings.
Dual Function CSO or HSO Output Sync Signal at TTL Level.
Multifunction Pin. VSO Output Sync Signal at TTL level. CLAMP TTL Output Signals
can be used to drive external circuitry to enable clamping of all Video Signals.
Input signal to select PAL or NTSC mode of operation, pin set to Logic 1 selects PAL.
No Connect.
Teletext Data Input Pin.
REF
cannot be used in 4¥ oversampling mode.
PIN FUNCTION DESCRIPTIONS
–10–
REV. B
AA
AA
.
.