USB3315C-CP-TR Standard Microsystems (SMSC), USB3315C-CP-TR Datasheet - Page 3

• Manufacturer Part Number: USB3315C-CP-TR
• Manufacturer: Standard Microsystems (SMSC)

Specifications of USB3315C-CP-TR

• Number Of Transceivers: 1
• Esd Protection: YeskV
• Power Supply Requirement: Triple
• Operating Supply Voltage (typ): Not RequiredV
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (max): Not RequiredV
• Operating Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (typ): 1.8/2.5/3.3/5V
• Mounting: Surface Mount
• Operating Temperature (max): 85C
• Operating Temperature (min): -40C
• Lead Free Status / RoHS Status: Compliant

Hi-Speed USB Transceiver with 1.8V-3.3V ULPI Interface - 24MHz Reference Clock
General Description
SMSC USB3315 REV C
CPEN
VBUS
DM
The USB3315 is a highly integrated Hi-Speed USB 2.0 Transceiver (PHY) that supports systems
architectures based on a 24MHz reference clock. It is designed to be used in both commercial and
industrial temperature applications.
The USB3315 meets all of the electrical requirements to be used as a Hi-Speed USB Host, Device,
or an On-the-Go (OTG) device. In addition to the supporting USB signaling the USB3315 also provides
USB UART mode.
USB3315 uses the industry standard UTMI+ Low Pin Interface (ULPI) to connect the USB PHY to the
Link. The industry standard ULPI interface uses a method of in-band signaling and status byte transfers
between the Link and PHY, to facilitate a USB session. By using in-band signaling and status byte
transfers the ULPI interface requires only 12 pins.
The USB3315 uses SMSC’s “wrapper-less” technology to implement the ULPI interface. This “wrapper-
less” technology allows the PHY to achieve a low latency transmit and receive time. SMSC’s low
latency transceiver allows an existing UTMI Link to be reused by adding a UTMI to ULPI bridge. By
adding a bridge to the ASIC the existing and proven UTMI Link IP can be reused.
The USB3315 is designed to run with a 24MHz reference clock. By using a reference clock from the
Link the USB3315 is able to remove the cost of a crystal reference from the design.
The USB3315 includes a integrated 3.3V LDO regulator to generate its own supply from power applied
at the VBAT pin. The voltage on the VBAT pin can range from 3.1 to 5.5V. The regulator dropout
voltage is less than 100mV which allows the PHY to continue USB signaling when the voltage on
VBAT drops to 3.1V. The USB transceiver will continue to operate at lower voltages, although some
parameters may be outside the limits of the USB specifications. If the user would like to provide a 3.3V
supply to the USB3315, the VBAT and VDD33 pins should be connected together.
The USB3315 also includes integrated pull-up resistors that can be used for detecting the attachment
of a USB Charger. By sensing the attachment to a USB Charger, a product using the USB3315 can
charge its battery at more than the 500mA allowed when charging from a USB Host.
DP
ID
Transceiver
Hi-Speed
Carkit
OTG
USB
Figure 1 USB3315 Block Diagram
PRODUCT PREVIEW
Integrated
Low Jitter
Registers
and State
3
REFCLK
Machine
ULPI
PLL
ULPI Interface
Management
Integrated
DATA[7:0]
Power
BIAS
Revision 2.1 (06-02-10)
RBIAS
RESETB
VBAT
VDD33
VDD18
VDDIO
STP
NXT
DIR
CLKOUT