TC1301A-AAAVMFTR Microchip Technology, TC1301A-AAAVMFTR Datasheet - Page 12
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
TC1301A-AAAVMFTR
Manufacturer Part Number
TC1301A-AAAVMFTR
Description
Dual CMOS LDO 300mA & 150mA W Shutdown, Voltage Detect, Bypass & Independent Del
Manufacturer
Microchip Technology
Datasheet
1.TC1301A-ADAVUA.pdf
(28 pages)
Specifications of TC1301A-AAAVMFTR
Regulator Topology
Positive Fixed
Voltage - Output
3.3V, 2.63V (Reset)
Voltage - Input
2.7 ~ 6 V
Voltage - Dropout (typical)
0.104V @ 300mA, 0.15V @ 150mA
Number Of Regulators
2
Current - Output
300mA (Min), 150mA (Min)
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
8-DFN
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Limit (min)
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
TC1301A/B
3.0
The descriptions of the pins are listed in
TABLE 3-1:
3.1
The push-pull output pin is used to monitor the voltage
on the V
threshold voltage, the RESET output will be held in the
low state. As the V
the RESET output will remain in the low state for
300 ms and then change to the high state, indicating
that the voltage on the V
3.2
Connect V
capacitor and load. It is capable of 300 mA maximum
output current. V
available; there is no pin to turn it OFF. See TC1301B
if ON/OFF control of V
3.3
Connect GND to the negative side of the input and
output capacitor. Only the LDO internal circuitry bias
current flows out of this pin (200 µA maximum).
3.4
By connecting an external 10 nF capacitor (typical) to
the bypass input, both outputs (V
have less noise and improved Power Supply Ripple
Rejection (PSRR) performance. The LDO output
voltage start-up time will increase with the addition of
an external bypass capacitor. By leaving this pin
unconnected, the start-up time will be minimized.
DS21798C-page 12
Pin No.
1
2
3
4
5
6
7
8
DET
TC1301A PIN DESCRIPTIONS
RESET Output Pin
Regulated Output Voltage #1
(V
Circuit Ground Pin (GND)
Reference Bypass Input
OUT1
OUT1
pin. If the V
SHDN2
RESET
Bypass
V
V
OUT1
Name
to the positive side of the V
V
)
GND
TC1301A PIN FUNCTION TABLE
OUT1
OUT2
V
DET
DET
IN
OUT1
output is available when V
pin rises above the threshold,
DET
DET
is desired.
Push-pull output pin that will remain low while V
300 ms after V
Regulated output voltage #1 capable of 300 mA.
Circuit ground pin.
Internal reference bypass pin. A 10 nF external capacitor can be used to further reduce
output noise and improve PSRR performance.
Output #2 shutdown control Input.
Regulated output voltage #2 capable of 150 mA.
Unregulated input voltage pin.
Input pin for Voltage Detector (V
pin is above the threshold.
voltage is less than the
OUT1
and V
Table
DET
OUT2
3-1.
rises above the reset threshold.
OUT1
) will
IN
is
DET
3.5
ON/OFF control is performed by connecting SHDN2 to
its proper level. When the input of this pin is connected
to a voltage less than 15% of V
this pin is connected to a voltage that is greater than
45% of V
3.6
Connect V
capacitor and load. This pin is capable of a maximum
output current of 150 mA. V
OFF using SHDN2.
3.7
Connect the unregulated input voltage source to V
the input voltage source is located more than several
inches away, or is a battery, a typical input capacitance
of 1 µF to 4.7 µF is recommended.
3.8
The voltage on the input of V
preset V
the threshold, the RESET output will be low. If the
voltage is above the V
will be high after the RESET time period. The I
supply current is typically 9 µA at room temperature,
with V
).
Function
DET
DET
Output Voltage #2 Shutdown
(SHDN2)
Regulated Output Voltage #2
(V
Unregulated Input Voltage Pin
(V
Input Pin for Voltage Detector
(V
IN
= 3.8V.
, V
OUT2
OUT2
IN
DET
DET
threshold voltage. If the voltage is below
OUT2
)
)
is below the reset threshold and for
to the positive side of the V
)
will be turned ON.
DET
© 2008 Microchip Technology Inc.
threshold, the RESET output
OUT2
DET
IN
can be turned ON and
, V
is compared with the
OUT2
will be OFF. If
OUT2
IN
DET
. If