PIC24FJ64GA004T-I/ML Microchip Technology, PIC24FJ64GA004T-I/ML Datasheet - Page 54

• Manufacturer Part Number: PIC24FJ64GA004T-I/ML
• Description: 64KB, Flash, 8192bytes-RAM, 16MIPS, 35I/O, 16-bit Family,nanoWatt 44 QFN 8x8x0.9
• Manufacturer: Microchip Technology
• Series: PIC® 24Fr

Specifications of PIC24FJ64GA004T-I/ML

• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 32MHz
• Connectivity: I²C, PMP, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 35
• Program Memory Size: 64KB (22K x 24)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-QFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DM240011 - KIT STARTER MPLAB FOR PIC24F MCUAC162088 - HEADER MPLAB ICD2 24FJ64GA004 28AC164336 - MODULE SOCKET FOR PM3 28/44QFNDV164033 - KIT START EXPLORER 16 MPLAB ICD2
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: PIC24FJ64GA004T-I/MLTR

PIC24FJ64GA004 FAMILY
5.5.2
If a Flash location has been erased, it can be pro-
grammed using table write instructions to write an
instruction word (24-bit) into the write latch. The
TBLPAG register is loaded with the 8 Most Significant
Bytes of the Flash address. The TBLWTL and TBLWTH
EXAMPLE 5-4:
DS39881D-page 54
; Setup a pointer to data Program Memory
; Setup NVMCON for programming one word to data Program Memory
MOV
MOV
MOV
MOV
MOV
TBLWTL W2, [W0]
TBLWTH W3, [W0++]
MOV
MOV
DISI
MOV
MOV
MOV
MOV
BSET
NOP
NOP
PROGRAMMING A SINGLE WORD
OF FLASH PROGRAM MEMORY
#tblpage(PROG_ADDR), W0
W0, TBLPAG
#tbloffset(PROG_ADDR), W0
#LOW_WORD_N, W2
#HIGH_BYTE_N, W3
#0x4003, W0
W0, NVMCON
#5
#0x55, W0
W0, NVMKEY
#0xAA, W0
W0, NVMKEY
NVMCON, #WR
PROGRAMMING A SINGLE WORD OF FLASH PROGRAM MEMORY
;
;Initialize PM Page Boundary SFR
;Initialize a register with program memory address
;
;
; Write PM low word into program latch
; Write PM high byte into program latch
;
; Set NVMOP bits to 0011
; Disable interrupts while the KEY sequence is written
; Write the key sequence
; Start the write cycle
; 2 NOPs required after setting WR
;
instructions write the desired data into the write latches
and specify the lower 16 bits of the program memory
address to write to. To configure the NVMCON register
for a word write, set the NVMOP bits (NVMCON<3:0>)
to ‘0011’. The write is performed by executing the
unlock sequence and setting the WR bit (see
Example 5-4).
 2010 Microchip Technology Inc.