PIC24FJ64GA002T-I/SO Microchip Technology, PIC24FJ64GA002T-I/SO Datasheet - Page 23

• Manufacturer Part Number: PIC24FJ64GA002T-I/SO
• Description: 64KB, Flash, 8192bytes-RAM, 16MIPS, 21I/O, 16-bit Family,nanoWatt 28 SOIC .300in
• Manufacturer: Microchip Technology
• Series: PIC® 24Fr

Specifications of PIC24FJ64GA002T-I/SO

• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 32MHz
• Connectivity: I²C, PMP, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 21
• Program Memory Size: 64KB (22K x 24)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DM240011 - KIT STARTER MPLAB FOR PIC24F MCUAC162088 - HEADER MPLAB ICD2 24FJ64GA004 28AC164339 - MODULE SKT FOR PM3 28SOICDV164033 - KIT START EXPLORER 16 MPLAB ICD2
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: PIC24FJ64GA002T-I/SOTR

3.8
Reading from code memory is performed by executing
a series of TBLRD instructions and clocking out the data
using the REGOUT command.
Table 3-8 shows the ICSP programming details for
reading code memory. In Step 1, the Reset vector is
exited. In Step 2, the 24-bit starting source address for
reading is loaded into the TBLPAG register and W6
register. The upper byte of the starting source address
is stored in TBLPAG and the lower 16 bits of the source
address are stored in W6.
TABLE 3-8:
© 2008 Microchip Technology Inc.
Step 1: Exit Reset vector.
Step 2: Initialize TBLPAG and the Read Pointer (W6) for TBLRD instruction.
Step 3: Initialize the Write Pointer (W7) to point to the VISI register.
Step 4: Read and clock out the contents of the next two locations of code memory, through the VISI register, using
Step 5: Reset device internal PC.
Step 6: Repeat Steps 4 and 5 until all desired code memory is read.
Command
(Binary)
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0001
0000
0000
0000
0000
0000
0000
0000
0001
0000
0000
0000
0000
0001
0000
0000
0000
Reading Code Memory
the REGOUT command.
SERIAL INSTRUCTION EXECUTION FOR READING CODE MEMORY
000000
040200
000000
200xx0
880190
2xxxx6
207847
000000
BA0B96
000000
000000
<VISI>
000000
BADBB6
000000
000000
BAD3D6
000000
000000
<VISI>
000000
BA0BB6
000000
000000
<VISI>
000000
040200
000000
(Hex)
Data
NOP
GOTO
NOP
MOV
MOV
MOV
MOV
NOP
TBLRDL
NOP
NOP
Clock out contents of VISI register
NOP
TBLRDH.B [W6++], [W7++]
NOP
NOP
TBLRDH.B [++W6], [W7--]
NOP
NOP
Clock out contents of VISI register
NOP
TBLRDL
NOP
NOP
Clock out contents of VISI register
NOP
GOTO
NOP
0x200
#<SourceAddress23:16>, W0
W0, TBLPAG
#<SourceAddress15:0>, W6
#VISI, W7
[W6], [W7]
[W6++], [W7]
0x200
To minimize the reading time, the packed instruction
word format that was utilized for writing is also used for
reading (see Figure 3-6). In Step 3, the Write Pointer,
W7, is initialized. In Step 4, two instruction words are
read from code memory and clocked out of the device,
through the VISI register, using the REGOUT
command. Step 4 is repeated until the desired amount
of code memory is read.
PIC24FJXXXGA0XX
Description
DS39768D-page 23