MIC5320-KGYMT TR Micrel Inc, MIC5320-KGYMT TR Datasheet - Page 10

• Manufacturer Part Number: MIC5320-KGYMT TR
• Description: Dual 150mA LDO Thin MLFr Dual Enable ( )
• Manufacturer: Micrel Inc

Specifications of MIC5320-KGYMT TR

• Regulator Topology: Positive Fixed
• Voltage - Output: 2.6V, 1.8V
• Voltage - Input: 2.3 ~ 5.5 V
• Voltage - Dropout (typical): 0.035V @ 150mA
• Number Of Regulators: 2
• Current - Output: 150mA
• Current - Limit (min): 300mA
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 6-TMLF®, QFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 576-2870-2; MIC5320-KGYMT TR; MIC5320-KGYMTTR; MIC5320-KGYMTTR

Micrel, Inc.
Applications Information
Enable/Shutdown
The MIC5320 comes with dual active-high enable pins
that
independently. Forcing the enable pin low disables the
regulator and sends it into a “zero” off-mode-current
state. In this state, current consumed by the regulator
goes nearly to zero. Forcing the enable pin high
enables the output voltage. The active-high enable pin
uses CMOS technology and the enable pin cannot be
left floating; a floating enable pin may cause an
indeterminate state on the output.
Input Capacitor
The MIC5320 is a high-performance, high bandwidth
device. Therefore, it requires a well-bypassed input
supply for optimal performance. A 1µF capacitor is
required from the input to ground to provide stability.
Low-ESR
performance at a minimum of space. Additional high-
frequency capacitors, such as small-valued NPO
dielectric-type
frequency noise and are good practice in any RF-
based circuit.
Output Capacitor
The MIC5320 requires an output capacitor of 1µF or
greater to maintain stability. The design is optimized
for use with low-ESR ceramic chip capacitors. High
ESR capacitors may cause high frequency oscillation.
The
performance has been optimized for a 1µF ceramic
output capacitor and does not improve significantly
with larger capacitance.
X7R/X5R
recommended
performance.
capacitance by 15% over their operating temperature
range and are the most stable type of ceramic
capacitors. Z5U and Y5V dielectric capacitors change
value by as much as 50% and 60%, respectively, over
their operating temperature ranges. To use a ceramic
chip capacitor with Y5V dielectric, the value must be
much higher than an X7R ceramic capacitor to ensure
the same minimum capacitance over the equivalent
operating temperature range.
No-Load Stability
Unlike many other voltage regulators, the MIC5320
will remain stable and in regulation with no load. This
is especially important in CMOS RAM keep-alive
applications.
February 2011
output
allow
dielectric-type
ceramic
each
capacitor
capacitors,
because
X7R-type
regulator
capacitors
can
ceramic
of
help
capacitors
be
their
to
provide
filter
increased,
capacitors
be
temperature
out
disabled
change
optimal
high-
are
but
10
Thermal Considerations
The MIC5320 is designed to provide 150mA of
continuous current for both outputs in a very small
package. Maximum ambient operating temperature
can be calculated based on the output current and the
voltage drop across the part. Given that the input
voltage is 3.3V, the output voltage is 2.8V for V
1.5V for V
actual power dissipation of the regulator circuit can be
determined using the equation:
Because this device is CMOS and the ground current
is typically <150µA over the load range, the power
dissipation contributed by the ground current is < 1%
and can be ignored for this calculation.
To determine the maximum ambient operating
temperature of the package, use the junction-to-
ambient thermal resistance of the device and the
following basic equation:
T
the die θ
The table below shows junction-to-ambient thermal
resistance for the MIC5320 in different packages.
6-Pin 1.6x1.6 Thin MLF
J(max)
= 125°C, the maximum junction temperature of
Package
P
V
P
150mA
P
P
JA
D
IN
D
D
D(MAX)
OUT2
thermal resistance = 100°C/W.
= 0.345W
= (V
= (3.3V – 2.8V) × 150mA + (3.3V -1.5) ×
I
GND
and the output current = 150mA. The
IN
=
Thermal Resistance
– V
⎛
⎝
®
OUT1
T
J(MAX)
) I
Minimum Footprint
θ
JA
OUT1
JA
- T
Recommended
100°C/W
+ (V
A
IN
M9999-021111-H
– V
OUT2
MIC5320
) I
OUT2
OUT1
2°C/W
θ
+
JC
,