MIC22600YTSE Micrel Inc, MIC22600YTSE Datasheet - Page 19

• Manufacturer Part Number: MIC22600YTSE
• Description: 1MHz 6A Integrated Switch Synchronous Buck Regulator
• Manufacturer: Micrel Inc
• Type: Step-Down (Buck), PWM - Voltage Moder

Specifications of MIC22600YTSE

• Internal Switch(s): Yes
• Synchronous Rectifier: Yes
• Number Of Outputs: 1
• Voltage - Output: Adj to 0.7V
• Current - Output: 6A
• Frequency - Switching: 1MHz
• Voltage - Input: 2.6 ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 24-TSSOP Exposed Pad, 24-eTSSOP, 24-HTSSOP
• Voltage - Supply: 2.6 V ~ 5.5 V
• Frequency-max: 1.2MHz
• Duty Cycle: 100%
• Pwm Type: Voltage Mode
• Buck: Yes
• Boost: No
• Flyback: No
• Inverting: No
• Doubler: No
• Divider: No
• Cuk: No
• Isolated: No
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: MIC22600YTSE

PCB Layout Guideline
Warning!!! To minimize EMI and output noise, follow
these layout recommendations.
PCB Layout is critical to achieve reliable, stable and
efficient performance. A ground plane is required to
control EMI and minimize the inductance in power,
signal and return paths.
The following guidelines should be followed to insure
proper operation of the MIC22602 converter.
IC
•
•
•
•
•
Input Capacitor
•
•
•
•
•
•
•
•
•
Micrel, Inc.
October 2009
Place the IC close to the point of load (POL).
Use fat traces to route the input and output power
lines.
The exposed pad (EP) on the bottom of the IC must
be connected to the ground.
Use several vias to connect the EP to the ground
plane, layer 2.
Signal and power grounds should be kept separate
and connected at only one location.
Place the input capacitor next.
Place the input capacitors on the same side of the
board and as close to the IC as possible.
Place a 22µF/6.3V ceramic bypass capacitor next to
each of the 4 PVIN pins.
Keep both the VIN and PGND connections short.
Place several vias to the ground plane close to the
input capacitor ground terminal, but not between the
input capacitors and IC pins.
Use either X7R or X5R dielectric input capacitors.
Do not use Y5V or Z5U type capacitors.
Do not replace the ceramic input capacitor with any
other type of capacitor. Any type of capacitor can be
placed in parallel with the input capacitor.
If a Tantalum input capacitor is placed in parallel
with the input capacitor, it must be recommended for
switching regulator applications and the operating
voltage must be derated by 50%.
In “Hot-Plug” applications, a Tantalum or Electrolytic
bypass capacitor must be used to limit the over-
voltage spike seen on the input supply with power is
suddenly applied.
19
Inductor
•
•
•
•
Output Capacitor
•
•
•
Diode
•
•
•
Keep the inductor connection to the switch node
(SW) short.
Do not route any digital lines underneath or close to
the inductor.
Keep the switch node (SW) away from the feedback
(FB) pin.
To minimize noise, place a ground plane underneath
the inductor.
Use a wide trace to connect the output capacitor
ground terminal to the input capacitor ground
terminal.
Phase margin will change as the output capacitor
value and ESR changes. Contact the factory if the
output capacitor is different from what is shown in
the BOM.
The feedback trace should be separate from the
power trace and connected as close as possible to
the output capacitor. Sensing a long high current
load trace can degrade the DC load regulation.
Place the Schottky diode on the same side of the
board as the IC and input capacitor.
The connection from the Schottky diode’s Anode to
the input capacitors ground terminal must be as
short as possible.
The diode’s Cathode connection to the switch node
(SW) must be keep as short as possible.
M9999-102809-C
MIC22600