MIC2005-0.5YML TR Micrel Inc, MIC2005-0.5YML TR Datasheet - Page 22
![Fixed Current Limit Single High-Side Switch + Flag + Cslew - 0.5A ( )](/photos/7/47/74764/576-6-mlf_sml.jpg)
MIC2005-0.5YML TR
Manufacturer Part Number
MIC2005-0.5YML TR
Description
Fixed Current Limit Single High-Side Switch + Flag + Cslew - 0.5A ( )
Manufacturer
Micrel Inc
Type
High Side Switchr
Datasheet
1.MIC2009YM6_TR.pdf
(29 pages)
Specifications of MIC2005-0.5YML TR
Number Of Outputs
1
Rds (on)
100 mOhm
Internal Switch(s)
Yes
Current Limit
500mA
Voltage - Input
2.5 ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
6-MLF®, QFN
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
576-1678-2
MIC2005-0.5YMLTR
MIC2005-0.5YMLTR
MIC2005-0.5YMLTR
MIC2005-0.5YMLTR
Variable Under Voltage Lock Out (VUVLO)
Only parts in bold have VUVLO.
V
switch in enabled. The V
voltage, indicating excessive loading of the V
When V
(V
switch to protect the supply and allow V
After 128ms has elapsed, the MIC20X6 enables switch.
This disable and enable cycling will continue as long as
V
(V
V
divider from V
ENABLE
Only parts in bold have ENABLE pin.
ENABLE pin is a logic compatible input which activates
the main MOSFET switch thereby providing power to the
V
LOW control signal. The MIC20XX can operate with
logic running from supply voltages as low as 1.5 V.
ENABLE may be driven higher than V
than 5.5V and not less than –0.3V.
FAULT/
Only parts in bold have FAULT/ pin.
FAULT/ is an N-channel open-drain output, which is
asserted (LOW true) when switch either begins current
limiting or enters thermal shutdown.
FAULT/ asserts after a brief delay when events occur
that may be considered possible faults. This delay
insures that FAULT/ is asserted only upon valid,
enduring, over-current conditions and that transitory
event error reports are filtered out.
In MIC200X FAULT/ asserts after a brief delay period, of
32ms typical. After a fault clears, FAULT/ remains
asserted for the delay period of 32ms
MIC201X’s FAULT/ asserts at the end of the Kickstart™
period which is 128ms typical. This masks initial current
surges, such as would be seen by a motor load starting
up. If the load current remains above the current limit
threshold after the Kickstart™ has timed out, then the
FAULT/ will be asserted. After a fault clears, FAULT/
remains asserted for the delay of 128ms.
Because FAULT/ is an open-drain it must be pulled
HIGH with an external resistor and it may be wire-OR’d
February 2011
UVLO
IN
UVLO
OUT
2003
2013
2003
2013
2003
2013
Micrel, Inc.
VUVLO_TH
VUVLO_TH
deceases below the V
pin. ENABLE is either an active HIGH or active
functions as an input voltage monitor when the
voltage is commonly established by a voltage
IN
2004
2014
2004
2014
2004
2014
) for 32ms or more, the MIC20XX disables the
) which has a typical value of 250mV. The
is less than the V
IN
-to-GND.
2005X
2005X
2005X
2015
2015
2015
IN
2006
2016
2006
2016
2006
2016
pin is monitored for a drop in
UVLO
ULVO
2007
2017
2007
2017
2007
2017
threshold voltage
threshold voltage
IN
2008
2018
2008
2018
2008
2018
, but no higher
IN
to recover.
IN
2009X
2019X
2009X
2019X
2009X
2019X
supply.
22
with other similar outputs, sharing a single pull-up
resistor. FAULT/ may be tied to a pull-up voltage source
which is higher than V
Soft-start Control
Large capacitive loads can create significant inrush
current surges when charged through the switch. For
this reason, the MIC20XX family of switches provides a
built-in soft-start control to limit the initial inrush currents.
Soft-start is accomplished by controlling the power
MOSFET when the ENABLE pin enables the switch.
C
Only parts in bold have CSLEW pin.
(Not available in 5-pin SOT-23 packages)
The C
output voltage ramp at turn-on. This input allows
designers the option of decreasing the output’s slew rate
(slowing the voltage rise) by adding an external
capacitance between the C
Thermal Shutdown
Thermal shutdown is employed to protect the MIC20XX
family of switches from damage should the die
temperature exceed safe operating levels. Thermal
shutdown shuts off the output MOSFET and asserts the
FAULT/ output if the die temperature reaches 145°C.
The switch will automatically resume operation when the
die temperature cools down to 135°C. If resumed
operation results in reheating of the die, another
shutdown cycle will occur and the switch will continue
cycling between ON and OFF states until the overcurrent
condition has been resolved.
Depending on PCB layout, package type, ambient
temperature, etc., hundreds of milliseconds may elapse
from the incidence of a fault to the output MOSFET
being shut off. This delay is due to thermal time
constants within the system itself. In no event will the
device be damaged due to thermal overload because die
temperature is monitored continuously by on-chip
circuitry.
SLEW
2003
2013
SLEW
2004
2014
pin is provided to increase control of the
2005X
2015
IN
, but no greater than 5.5V.
2006
2016
SLEW
and V
2007
2017
IN
MIC20xx Family
M9999-020311-D
pins.
2008
2018
2009X
2019X