MCP4716A1T-E/CH Microchip Technology, MCP4716A1T-E/CH Datasheet - Page 12
![Single, 10-bit NV DAC With Ext Vref And I2C Interface 6 SOT-23 T/R](/photos/16/3/160337/6-sot23-large-300dpi-lyrd_sml.jpg)
MCP4716A1T-E/CH
Manufacturer Part Number
MCP4716A1T-E/CH
Description
Single, 10-bit NV DAC With Ext Vref And I2C Interface 6 SOT-23 T/R
Manufacturer
Microchip Technology
Series
-r
Datasheet
1.MCP4706A0T-ECH.pdf
(86 pages)
Specifications of MCP4716A1T-E/CH
Number Of Converters
1
Conversion Rate
1
Resolution
10 bit
Interface Type
I2C
Settling Time
6 us
Supply Voltage (max)
5.5 V
Supply Voltage (min)
2.7 V
Maximum Operating Temperature
+ 125 C
Mounting Style
SMD/SMT
Package / Case
SOT-23-6
Maximum Power Dissipation
452 mW
Minimum Operating Temperature
- 40 C
Supply Current
210 uA
Number Of Bits
10
Data Interface
EEPROM, I²C, Serial
Voltage Supply Source
Single Supply
Power Dissipation (max)
452mW
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Number Of Outputs And Type
*
Lead Free Status / Rohs Status
Details
MCP4706/4716/4726
TABLE 1-3:
DS22272A-page 12
I
Note 1:
2
Param.
C AC Characteristics
No.
106
107
109
110
2:
3:
4:
5:
6:
7:
8:
As a transmitter, the device must provide this internal minimum delay time to bridge the undefined region
(minimum 300 ns) of the falling edge of SCL to avoid unintended generation of START or STOP conditions.
A fast-mode (400 kHz) I
requirement t
stretch the LOW period of the SCL signal. If such a device does stretch the LOW period of the SCL signal,
it must output the next data bit to the SDA line.
T
the SCL line is released.
The MCP47X6 device must provide a data hold time to bridge the undefined part between V
the falling edge of the SCL signal. This specification is not a part of the I
in order to ensure that the output data will meet the setup and hold specifications for the receiving device.
Use C
Not Tested. This parameter ensured by characterization.
A Master Transmitter must provide a delay to ensure that difference between SDA and SCL fall times do
not unintentionally create a Start or Stop condition.
If this parameter is too short, it can create an unintentional Start or Stop condition to other devices on the
I
affected.
Ensured by the T
The specification is not part of the I 2 C specification. T
2
R
T
T
C bus line. If this parameter is too long, the Data Input Setup (T
HD:DAT
SU:DAT
T
Sym
max.+t
T
BUF
AA
b
I
2
in pF for the calculations.
C BUS DATA REQUIREMENTS (SLAVE MODE) (CONTINUED)
Data Input: This parameter must be longer than t
Data Output: This parameter is characterized, and tested indirectly by testing T
SU;DAT
Characteristic
Bus free time
Data input setup
Data input hold
SU;DAT
Output valid
from clock
AA
= 1000 + 250 = 1250 ns (according to the standard-mode I
time
time
3.4 MHz specification test.
≥ 250 ns must then be met. This will automatically be the case if the device does not
2
C-bus device can be used in a standard-mode (100 kHz) I
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
Operating Voltage V
100 kHz mode
400 kHz mode
1.7 MHz mode
3.4 MHz mode
100 kHz mode
400 kHz mode
1.7 MHz mode
3.4 MHz mode
100 kHz mode
400 kHz mode
1.7 MHz mode
3.4 MHz mode
100 kHz mode
400 kHz mode
1.7 MHz mode
3.4 MHz mode
DD
4700
1300
N.A.
N.A.
range is described in
Min
250
100
10
10
—
—
—
—
—
AA
0
0
0
0
= T
–40°C ≤ T
SP
HD:DAT
.
3750
1200
Max
150
310
150
—
—
—
—
—
—
—
—
—
—
—
—
SU:DAT
+ T
A
≤ +125°C (Extended)
FSDA
2
Units
) or Clock Low time (T
C specification, but must be tested
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Electrical characteristics
© 2011 Microchip Technology Inc.
2
(or T
C bus specification) before
2.7V-5.5V,
2.7V-5.5V,
4.5V-5.5V,
4.5V-5.5V,
Note 2
Note
Cb = 100 pF,
Note
Cb = 400 pF,
Note
Cb = 100 pF,
Note
Time the bus must be free
before a new transmission
can start
RSDA
2
C-bus system, but the
1,
1,
1,
1,
).
Conditions
Note 8
Note
Note
Note 8
AA
Note 6
Note 6
Note 6
Note 6
IH
parameter.
7,
5,
LOW
and V
Note 8
Note 8
) can be
IL
of