100DFC6-P Tyco Electronics, 100DFC6-P Datasheet - Page 12

• Manufacturer Part Number: 100DFC6-P
• Description: CAP FEEDTHROUGH DFC 100A Y4
• Manufacturer: Tyco Electronics
• Series: DFCr

Specifications of 100DFC6-P

• Capacitance: 1.0µF
• Voltage: 130V
• Current: 100A
• Operating Temperature: -40°C ~ 60°C
• Package / Case: Panel Mount
• Current Rating: 100A
• Terminal Type: M8
• Features: Y4 Capacitor Class
• Voltage Rating: 130V
• Operating Temperature Min: -40°C
• Filter Type: Feed Through
• Mounting Type: M24
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Dc Resistance (dcr): -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 1-1609992-8; CCM1806

INSTALLATION, BACKGROUND, AND SAFETY
FEEDTHROUGH CAPACITOR PERFORMANCE
SAFETY
FOR MORE INFORMATION
• Feedthrough capacitors and filters are designed
• Normal two-terminal capacitors resonate with their
• This limits their use as suppression components
• Feedthrough capacitors have no major resonance as
• Performance continues to increase with frequency
• Feedthrough capacitors are essential for good high
• Feedthrough filters incorporate feedthrough
• As an example, this graph compares the perform-
• Relevant safety standards have been adhered to in
6-1773445-5 – 5M – GIC/FP – 01/07
Internet:
www.tycoelectronics.com
www.corcom.com
for through-bulkhead mounting for offering high
frequency filtering in line-to-ground applications.
They should be mounted through a metal bulkhead
or chassis. The bulkhead mounting surface should be
clean and unpainted to offer a low impedance patch
from the capacitor or filter to the equipment chassis.
Poor earth bonding will limit the available perform-
ance of the product and could compromise safety.
lead inductance in the region 1-10 MHz
above a few MHz
they have no lead inductance
frequency performance
capacitors for the same benefits
ance of a 1μF feedthrough capacitor with a 1μF
two-terminal capacitor
the design and manufacture of these products.
However, all capacitors will store charge after power
has been removed and must be treated with respect
as this can be lethal when the voltage and charge are
high enough. The filters and capacitors contained
within this catalog do not contain internal discharge
resistors. It is therefore recommended that they are
fitted with external discharge resistors to discharge
the capacitors after the power has been removed.
Where necessary, terminals should be enclosed by
the user to prevent any danger of electric shock or
accidental shorting. In all cases, capacitors and filters
should always be shorted to earth prior to touching
to ensure they are fully discharged.
E-mail:
[e-mail]
©2006 by Tyco Electronics Corporation. All Rights Reserved. CORCOM and TYCO are trademarks.
• Conductive paint finishes should be avoided as they
• The user should ensure he/she is familiar with
CORCOM Feedthrough
FEEDTHROUGH CAPACITOR PERFORMANCE
do not usually provide adequate conductivity. 2
spanners should be used when making electrical
connections to the terminals, and maximum tighten-
ing torque figures quoted should be observed.
restrictions on capacitance value, earth leakage
current, test voltage, and safety labeling require-
ments, which may be applicable to his/her particular
installation. In particular, safety standards IEC950
and EN60950, which most electrical equipment
needs to comply with, contain a number of
specific requirements for capacitors, which may
be applicable.
0.001
0.01
Filters and Capacitors
0.1
10
1
10K
100K
Technical Support:
USA: 1-800-468-2023
CORCOM Prods: 1-847-680-7400
Germany: 49-89-6089-0
Frequency (Hz)
1M
Theoretical
10M
Two-Terminal
Capacitor
Feedthrough
Actual
100M
10
20
30
40
50
60
70
80
90
100
0