0ICAB-001-XTP ON Semiconductor, 0ICAB-001-XTP Datasheet - Page 6

• Manufacturer Part Number: 0ICAB-001-XTP
• Manufacturer: ON Semiconductor

Specifications of 0ICAB-001-XTP

• Data Rate: 1000Kbps
• Number Of Transceivers: 1
• Standard Supported: ISO 11898-2
• Operating Supply Voltage (max): 5.25V
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (min): 4.75V
• Package Type: SOIC N
• Supply Current: 65mA
• Operating Temperature (max): 125C
• Operating Temperature (min): -40C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 8
• Lead Free Status / RoHS Status: Compliant

Operating Modes
illustrated in Table 5 below. In case the device is powered,
one of two operating modes can be selected through
Pin AUTB.
High−Speed Mode
is in its high−speed mode and is able to communicate via the
bus lines. The signals are transmitted and received to the
CAN controller via the pins TxD and RxD. The slopes on the
bus line outputs are optimized to give extremely low
electromagnetic emissions.
detect the used communication speed of other transmitting
network nodes. Bus communication is received and via the
RxD pin sent to the CAN controller. If the CAN controller
operates at the wrong baud rate, it will transmit an error
frame. This message will be looped back to the CAN
controller which will increment its error counter. The CAN
controller will be reset with another baud rate. When an
error−free message is received, the correct baud rate is
detected. A logic low may now be applied to Pin AUTB,
returning to the high−speed mode.
Table 5. FUNCTIONAL TABLE OF AMIS−42671 WHEN NOT CONNECTED TO THE BUS; x = don’t care
4.75 to 5.25 V
4.75 to 5.25 V
4.75 to 5.25 V
V
(unpowered)
PORL < V
The behavior of AMIS−42671 under various conditions is
If pin AUTB is pulled low (or left floating), the transceiver
In Autobaud mode the local CAN controller is able to
CC
< PORL
VCC
CC
< 4.75 V
(or floating)
(or floating)
Pin TxD
Figure 3. Simplified Schematic Diagram of Autobaud Function
AUTB
>2 V
RxD
TxD
0
1
1
x
PC20071002.4
(or floating)
Pin AUTB
FUNCTIONAL DESCRIPTION
0
1
x
x
x
http://onsemi.com
0 V < CANH <
0 V < CANH <
Pin CANH
V
V
6
High
V
V
CC
CC
CC
CC
/2
/2
Autobaud Mode
mode. The transmitter is disabled while the receiver remains
active. All other IC functions also continue to operate.
Normal bus activity can be monitored at the RxD pin and
transmit data on TxD is looped back to RxD without
influencing the CAN communication.
Overtemperature Detection
by switching off the transmitter if the junction temperature
exceeds a value of approximately 160°C. Because the
transmitter dissipates most of the power, the power
dissipation and temperature of the IC is reduced. All other
IC functions continue to operate. The transmitter off−state
resets when pin TxD goes high. The thermal protection
circuit is particularly necessary when a bus line
short−circuits.
If Pin AUTB is pulled high, AMIS−42671 is in Autobaud
A thermal protection circuit protects the IC from damage
0V < CANL <
0V < CANL <
Pin CANL
V
V
Low
V
V
CC
CC
CC
CC
/2
/2
CANH
CANL
Bus State
Recessive
Recessive
Recessive
Recessive
Dominant
Pin RxD
0
1
1
1
1