125800D00000G Aavid Thermalloy, 125800D00000G Datasheet - Page 101

• Manufacturer Part Number: 125800D00000G
• Description: SOLDER ANCHOR FOR BGA HEATSINKS
• Manufacturer: Aavid Thermalloy

Specifications of 125800D00000G

• Accessory Type: Solder Anchor (2 required)
• Packages Cooled: BGA
• Length: 7.62mm
• Rohs Compliant: Yes
• For Use With/related Products: Heat Sinks
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 43409

Thermalfilm™ Polyimide Plastic Films
Thermalfilm™ and Thermalfilm™ MT are low cost polymide plastic insulating films designed
to be an improved replacement for mica. These insulators have a distinctive amber color and
can be easily recognized and assembled on a production line.
Thermalfilm™ MT, made from high performance Kapton™ MT material, provides thermal
conductivity nearly 2-5 times greater than standard Thermalfilm™. Both insulators have an
extremely high resistance to flow or thin out under high compressive stresses, particularly at
elevated temperatures. Excellent physical, mechanical and electrical properties remain nearly
constant over a wide range of temperatures and frequencies. They are radiation resistant,
have no melting points, and have no known organic solvents. The polymide plastic film is UL
listed as a component in UL’s publication “Component – Plastic Material” dated September
18, 1969. The UL card number is E39505R, Guide QMFZ2 filed by E. I. du Pont de Nemours
& Co., Inc. Thermalfilm
ORDERING INFORMATION
For standard pre-cut sizes of Thermalfilm
and Thermafilm
www.aavidthermalloy.com
PROPERTY
Dielectric strength
Dielectric constant
Dissipation factor
Volume resistivity
Surface resistivity
Corona start voltage 0.025mm (1-mil)
Insulation resistance
Material thickness
Ultimate tensile strength (MD)
Bursting strength test (Mullen)
Tear strength – initial
Density
Folding endurance (MIT)
Melting point
Zero strength temperature
Cut through temperature
Service temperature
Thermal conductivity
Flammability
Notes: One mil equals 0.001 inch
Dimensional tolerances are ± 0.38mm (0.015”), hole diameters are ± 0.25mm (0.010”) and angularity is ± 1 1/2° unless otherwise specified.
TM
MT see page 102.
TM
is rated 94-V/0.
AMERICA
EUROPE
TM
Italy Tel: [phone] email: [e-mail]
United Kingdom Tel: [phone] email: [e-mail]
USA Tel: [phone] email: [e-mail]
Italy Tel: [phone] email: [e-mail]
United Kingdom Tel: [phone] email: [e-mail]
USA Tel: [phone] email: [e-mail]
THERMALFILM™
0.03mm (1-mil)
240 x 10
(6,100 volts/mil)
3.5
0.002
10
10
465 volts
100.000 megohm mfds.
0.05mm (0.002”)
1.72 x 10
3.10 x 10
27,559 gm/mm (700 gm/mil)
1.42 gm/cm
>10,000 cycles
NONE
815
435
525
-260
(-436
0.156W/m
(0.09 BTU/hr-ft-ºF)
V-0, UL “E” card E39505
17
16
º
º
º
C (1499
C (815
C (977
ohm-cm
ohms
º
C to 240
º
F to 464
3
8
5
volts/mm
Pa (25,000 psi)
Pa (45 psi)
º
º
F)
F)
º
ELECTRICAL – TYPICAL VALUE @ 25° C
C
º
3
F)
(88.7 lb/ft
º
C
º
F)
3
)
PHYSICAL
THERMAL
THERMALFILM™ MT
177.2 x 10
(4500 volts/mm)
4.3
0.002
10
10
465 volts
100.000 megohm mfds.
0.05mm (0.002”)
103 MPa (1500 psi)
0.31 MPa (45 psi)
35,433 gm/mm (900 gm/mil)
1.78 gm/cm
>10,000 cycles
NONE
815
435
525
-260
(-436
0.379 W/m
(0.219 BTU/hr-ft-
V-0, UL “E” card E39505
Thermalfilm™ and Thermalfilm™ MT
17
16
º
º
º
C (1499
C (815
C (977
ohm-cm
ohms
º
C to 240
º
F to 464
3
º
º
F)
F)
volts/mm
º
º
C
3
F)
(111.1 lb/ft
º
C
º
F)
ASIA
º
F)
Singapore Tel: [phone] email: [e-mail]
Taiwan Tel: [phone] email: [e-mail]
3
)
TEST METHOD
ASTM D149-64
ASTM D150-64T
ASTM D150-64T
ASTM D257-61
ASTM D257-61
ASTM D1868-61T
Based on 0.05 mfd wound
capacitor using 0.25 mm
(1-mil) Film
ASTM D882-64T
ASTM 0774-63
ASTM D1004-61
ASTM D1505-63T
ASTM D2176-63T
Hot Bar (Du Pont test)
Weighted probe on heated film
(Du Pont test)
Model TC-1000 twin heatmeter
Comparative tester
UL 94
101