R1G220-AB35-52 EBM-Papst Industries Inc, R1G220-AB35-52 Datasheet - Page 6

• Manufacturer Part Number: R1G220-AB35-52
• Description: IMPELLER MTRZD 220X63MM 24VDC
• Manufacturer: EBM-Papst Industries Inc
• Series: R1G220ABr
• Type: Impellersr

Specifications of R1G220-AB35-52

• Bearing Type: Ball
• Fan Type: Motorized Impellers
• Size / Dimension: Round - 220mm Dia x 71mm W
• Voltage - Rated: 24VDC
• Power (watts): 106W
• Features: PWM Control; Speed Sensor (Tach)
• Rpm: 3150 RPM
• Noise: 76 dB(A)
• Air Flow: 620.9 CFM (17.58m³/min)
• Termination: 4 Wire Leads
• Weight: 3.1 lbs (1.4kg)
• Current Rating: 5A
• Voltage Range: 16 ~ 28VDC
• Operating Temperature: -13 ~ 140°F (-25 ~ 60°C)
• Termination Style: 76 dB(A)
• External Depth: 71mm
• External Diameter: 220mm
• Current Type: DC
• Supply Voltage: 24VDC
• Flow Rate: 621CFM
• Noise Rating: 76dBA
• Power Connection Type: Lead Wires
• Airflow: 620.9 CFM
• Speed: 3150 RPM
• Frame Dimensions (mm): 220 mm x 71 mm
• Power Rating: 106 W
• Brand/series: R1G220 Series
• Dimensions: 8.66"Dia.x2.8"W
• Noise Level: 76 dBA
• Power, Rating: 106 W
• Size: Φ 220 mm (8.66")
• Special Features: Tachometer
• Temperature, Operating, Maximum: +60 °C
• Voltage, Rating: 24 VDC
• Wiring Connection: Red = +; Blue = – White = Tach Output; Yellow = Speed Control
• Recommended Inlet Ring: 9609-2-4013
• Diameter: 220mm
• Flow Rate - Imperial: 621CFM
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Static Pressure: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: R1G220AB3552

4. CONNECTION AND START-UP
4.1 Connecting the mechanical system
4.2 Connecting the electrical system
4.2.1 Prerequisites
4.3 Connection of the cables
External leads are brought out of device.
Item no.: 50745-5-9970 · Revision status: KM70943 · Print-out on 10/06/2010 · Created by Y. Uhlmann (VM-TDO) · Page 6 of 9
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · 74673 Mulfingen · Phone: [phone] · Fax: [phone] · www.ebmpapst.com · [e-mail]
R1G220-AB35-52
Install the device according to your application.
Check whether the data on the type plate agree with the connection
data.
Before connecting the device, ensure that the supply voltage matches
the operating voltage of the device.
Only use cables designed for current according to the type plate.
Connect the lines according to your application. When doing so,
observe chapter 4.4 Connection diagram.
CAUTION
Cutting and crushing hazard when removing the fan
from the packaging
CAUTION
Electrical voltage
The fan is a built-in component and features no electrically
isolating switch.
NOTE
Water penetration into leads or wires
Water enters at the cable end on the customers side and can
damage the device.
Operate the device with a safely isolated power pack.
Carefully seize the impeller to lift the device out of its
packaging. Make sure to avoid any shock.
Wear safety shoes and cut-resistant safety gloves.
Only connect the fan to circuits that can be switched off with
an all-pole separating switch.
When working on the fan, you must switch off the
installation/machine in which the fan is installed and secure it
from being switched on again.
Make sure that the cable end is connected in a dry
environment.
Operating instructions