2-1761607-6 TE Connectivity, 2-1761607-6 Datasheet - Page 4
![Conn Ejector Header HDR 16 POS 2.54mm Solder RA Thru-Hole](/photos/24/95/249527/42450302_sml.jpg)
2-1761607-6
Manufacturer Part Number
2-1761607-6
Description
Conn Ejector Header HDR 16 POS 2.54mm Solder RA Thru-Hole
Manufacturer
TE Connectivity
Type
Ejector Headerr
Series
AMP-LATCHr
Datasheet
1.1761681-9.pdf
(5 pages)
Specifications of 2-1761607-6
Pitch
2.54 mm
Number Of Rows
2
Number Of Contacts
16
Gender
HDR
Contact Plating
Gold Over Nickel
Termination Method
Solder
Connector Type
Wire To Board
Contact Termination
Right Angle Through Hole
No. Of Contacts
16
No. Of Rows
2
Pitch Spacing
2.54mm
Connector
RoHS Compliant
Product Type
Headers - Shrouded
Number Of Positions / Contacts
16
Mounting Style
Through Hole
Mounting Angle
Right
Termination Style
Solder
Housing Material
Thermoplastic
Contact Material
Phosphor Bronze
Product Line
AMP-LATCH
Profile
Low
Pcb Mounting Orientation
Right Angle
Pcb Mount Retention
Without
Mating Connector Lock
Without
Housing Style
4-Sided
Ejection Latches
With
Post Size (mm [in])
0.64 [.025]
Shrouded
Yes
[shrouded] End Dimension (mm [in])
3.81 [0.150]
Termination Post Length (mm [in])
2.60 [0.102]
Solder Tail Contact Plating
Tin over Nickel
Header Type
Pin Header
Number Of Positions
16
Centerline, Matrix (mm [in])
2.54 x 2.54 [.100 x .100]
Daisy Chain
With
Preloaded
Yes
Contact Plating, Mating Area, Material
Gold Flash over Palladium Nickel
Contact Shape
Square
Contact Base Material
Phosphor Bronze
Connector Style
Header - Pin
Mating Alignment Type
Center, Military
Mating Alignment
With
Ul Flammability Rating
UL 94V-0
Housing Color
Blue
Rohs/elv Compliance
RoHS compliant, ELV compliant
Lead Free Solder Processes
Wave solder capable to 240°C, Wave solder capable to 260°C, Wave solder capable to 265°C
Rohs/elv Compliance History
Always was RoHS compliant
Temperature Rating
Standard
Lead Free Status / Rohs Status
Details
4.
4.1.
4.2.
4.3.
4.4.
Rev F
QUALITY ASSURANCE PROVISIONS
Qualification Testing
A.
B.
Requalification Testing
If changes significantly affecting form , fit or function are m ade to the product or m anufacturing process,
product assurance shall coordinate requalification testing, consisting of all or part of the original testing
sequence as determ ined by developm ent/product, quality and reliability engineering.
Acceptance
Acceptance is based on verification that the product m eets the requirem ents of Figure 1. Failures
attributed to equipm ent, test setup or operator deficiencies shall not disqualify the product. W hen
product failure occurs, corrective action shall be taken and specim ens resubm itted for qualification.
Testing to confirm corrective action is required before resubm ittal.
Quality Conform ance Inspection
The applicable quality inspection plan will specify sam pling acceptable quality level to be used.
Dim ensional and functional requirem ents shall be in accordance with the applicable product drawing
and this specification.
Specim en Selection
Specim ens shall be prepared in accordance with applicable Instruction Sheets and shall be
selected at random from current production. All test groups shall each consist of a m inim um of 5
headers of each type.
Test Sequence
Qualification inspection shall be verified by testing specim ens as specified in Figure 2.
108-40018
4 of 5