746611-7 TE Connectivity, 746611-7 Datasheet - Page 93

• Manufacturer Part Number: 746611-7
• Description: Conn IDC Connector PL 8 POS 2.54mm IDT RA Cable Mount
• Manufacturer: TE Connectivity
• Type: IDC Connectorr
• Series: AMP-LATCHr

Specifications of 746611-7

• Pitch: 2.54 mm
• Number Of Rows: 2
• Number Of Contacts: 8
• Gender: PL
• Contact Plating: Gold Over Nickel
• Termination Method: IDT
• Connector Type: Wire To Board
• Contact Termination: IDC / IDT
• No. Of Contacts: 8
• No. Of Rows: 2
• Pitch Spacing: 2.54mm
• Rohs Compliant: Yes
• Product Line: AMP-LATCH
• Termination Method To Pc Board: Through Hole - Solder
• Pcb Mounting Orientation: Vertical
• Pcb Mount Retention: Without
• Pcb Mount Alignment: Without
• Termination Method To Wire/cable: IDC
• Ul File Number: E28476
• Csa File Number: LR 7189
• Contact - Rated Current (a): 1
• Operating Voltage Reference: AC
• Operating Voltage (vac): 250
• Wire/cable Size (awg): 26 – 30
• Wire/cable Size (mm²): 0.051 – 0.15
• Wire/cable Size (cma): 101 – 296
• Tail Length (mm [in]): 3.94 [0.155]
• Tail Orientation: In-line
• Profile Height (y-axis) (mm [in]): 6.43 [0.253]
• Number Of Positions: 8
• Centerline (mm [in]): 2.54 [0.100]
• Row-to-row Spacing (mm [in]): 2.54 [0.100]
• Length (x-axis) (mm [in]): 12.40 [0.4881]
• Width (z-axis) (mm [in]): 10.67 [0.420]
• Contact Type: Pin
• Contact Base Material: Phosphor Bronze
• Contact Plating, Mating Area, Material: Gold or Palladium Nickel or Performance Based
• Contact Plating, Mating Area, Thickness (µm [?in]): 0.762 [30]
• Tail Plating Material: Gold
• Tail Plating, Thickness (µm [?in]): 0.762 [30]
• Connector Style: Plug
• Housing Color: Black
• Ul Flammability Rating: UL 94V-0
• Rohs/elv Compliance: RoHS compliant, ELV compliant
• Lead Free Solder Processes: Wave solder capable to 240°C, Wave solder capable to 260°C, Wave solder capable to 265°C
• Rohs/elv Compliance History: Always was RoHS compliant
• Agency/standard: UL, CSA
• Ul Rating: Recognized
• Ul Voltage Rating (vac): 250
• Operating Temperature (°c [°f]): -65 – +105 [-85 – +221]
• Applies To: Printed Circuit Board
• Accepts Wire Insulation Diameter, Range (mm [in]): 0.81 – 1.07 [0.032 – 0.042]
• Pcb Thickness, Recommended (mm [in]): 3.18 [0.125]
• Application Use: Wire-to-Board
• Contact Transmits (typical Application): Signal (Data)
• Packaging Method: Tray

1. Place pinless header
2. With bottom of pc board
3. Apply an even, centered
over preinstalled posts
so that post tips start
into header cavities.
supported, place steel
block over header. Steel
block must be wider and
longer than header so
that it covers all four sides
of the header. However,
for headers with latches
pre-assembled, the steel
block must not interfere
with the latches.
force on steel block until
header bottoms on pc
board. If posts are
longer than .545 [13.84],
they may be forced
against the steel block
before the header is fully
seated. In this situation,
extreme caution must be
taken so that posts are
not damaged or pushed
out of the pc board.
93