D2E133-DM47-23 EBM-Papst Industries Inc, D2E133-DM47-23 Datasheet - Page 6

• Manufacturer Part Number: D2E133-DM47-23
• Description: BLWR DUAL CENT 204X232MM 230VAC
• Manufacturer: EBM-Papst Industries Inc
• Series: D2E133r

Specifications of D2E133-DM47-23

• Bearing Type: Ball
• Fan Type: Blower, Centrifugal
• Size / Dimension: Rectangular - 204mm L x 213mm H x 270mm W (133mm Dia)
• Voltage Rating: 230VAC
• Power (watts): 185W
• Rpm: 2200 RPM
• Noise: 55 dB(A)
• Air Flow: 353.0 CFM (9.99m³/min)
• Termination: 2 Wire Leads
• Weight: 10 lbs (4.5kg)
• Termination Style: 55 dB(A)
• External Height: 213mm
• External Width: 204mm
• External Depth: 270mm
• External Diameter: 145mm
• Current Type: AC
• Supply Voltage: 230VAC
• Flow Rate: 353CFM
• Noise Rating: 55dBA
• Product: Blowers
• Diameter: 145mm
• Flow Rate - Imperial: 353CFM
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Static Pressure: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: D2E133DM4723

4. CONNECTION AND START-UP
4.1 Connecting the mechanical system
4.2 Connecting the electrical system
4.2.1 Prerequisites
4.2.2 Voltage control
Item no.: 10985-5-9970 · Revision status: KM71618 · Print-out on 06/08/2010 · Created by Y. Uhlmann (VM-TDO) · Page 6 of 9
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · 74673 Mulfingen · Phone: [phone] · Fax: [phone] · www.ebmpapst.com · [e-mail]
D2E133-DM47-23
Install the device according to your application.
Check whether the data on the type plate agree with the connection
data and the data of the operating capacitor.
Before connecting the device, ensure that the supply voltage matches
the operating voltage of the device.
Only use cables designed for current according to the type plate.
CAUTION
Cutting and crushing hazard when removing the blower
from the packaging
DANGER
Electric voltage on the device
Electric shock
CAUTION
Electrical voltage
The blower is a built-in component and features no electrically
isolating switch.
NOTE
Water penetration into leads or wires
Water enters at the cable end on the customers side and can
damage the device.
Connect the device only to circuits that can be switched off
using an all-pole disconnecting switch.
With open loop speed control using transformers or electronic
voltage regulators (e.g. phase angle control), excessive current
may occur.
In addition, noises can occur with phase angle control
depending on the mounting situation.
Carefully lift the blower out of its packaging, only touching
the housing. Make sure to avoid any shock.
Wear safety shoes and cut-resistant safety gloves.
Always install a protective earth.
Check the protective earth.
Connect the blower only to circuits that can be switched off
using an all-pole disconnecting switch.
When working on the blower, you must switch off the
system/machine in which the blower is installed and secure
it from being switched on again.
Make sure that the cable end is connected in a dry
environment.
Operating instructions
4.2.3 Frequency inverter
4.3 Connection of the cables
External leads are brought out of device.
Connect the lines according to your application. When doing so,
observe chapter 4.4 Connection diagram.
Fit sinusoidal filters that work on all poles (live-live and live-
earth) between the frequency inverter and the motor for
operation with frequency inverters.
Depending on how the device is installed, noises may occur.