532436-1 TE Connectivity, 532436-1 Datasheet - Page 3

• Manufacturer Part Number: 532436-1
• Description: Conn HDI PL 100 POS 2.54mm Solder ST Thru-Hole
• Manufacturer: TE Connectivity
• Type: HDIr
• Series: AMP-HDI Seriesr

Specifications of 532436-1

• Pitch: 2.54 mm
• Number Of Rows: 4
• Number Of Contacts: 100
• Termination Method: Solder
• Mounting: Through Hole
• Contact Plating: Gold
• Mounting Style: Through Hole
• Product Type: Connector
• Gender: Plug
• Pcb Mount Style: Through Hole
• Pcb Mounting Orientation: Vertical
• Make First / Break Last: No
• Pcb Mount Retention: Without
• Termination Post Length (mm [in]): 4.83 [0.190]
• Solder Tail Contact Plating: Tin
• Number Of Positions: 100
• Centerline (mm [in]): 2.54 [0.100]
• Contact Configuration: Four-Beam
• Contact Plating, Mating Area, Material: Gold (30)
• Contact Base Material: Phosphor Bronze
• Underplate Material: Nickel
• Mating Alignment: Without
• Housing Material: PPS
• Housing Color: Brown
• Housing Material Temperature: High
• Center Guide: Without
• Government/industry Qualification: No
• Rohs/elv Compliance: ELV compliant, 5 of 6 Compliant
• Lead Free Solder Processes: Not suitable for lead free processing
• Lead Free Status / Rohs Status: No

Unm ating force.
Contact retention.
Contact engaging force.
Contact separating force.
Durability.
Resistance to soldering heat.
Insertion force, ACTION PIN.
Retention force, ACTION PIN.
Torque, ACTION PIN.
Therm al shock.
Hum idity-tem perature cycling.
Rev C
Test Description
No physical dam age.
40 pounds m axim um per pin.
Pin shall not dislodge from printed
.4 ounces m inim um average per
contact.
Contacts shall not dislodge from its
norm al locking position.
4 ounces m axim um per contact.
.1 ounce m inim um .
No physical dam age.
.020 ohm s m axim um term ination
resistance, low level.
Contact separation force.
wiring board.
Pin shall not m ove or dislodge from
printed wiring board.
.020 ohm s m axim um term ination
resistance, low level.
1000 m egohm s final insulation
resistance.
ENVIRONMENTAL
Figure 1 (end)
Requirem ent
Measure force to engage using
Size 3 tim es using gage 2, insert
Subject term inal posts m ounted on
Fully insert pin into printed wiring
Measure force necessary to unm ate
connector assem bly.
Calculate force per contact.
TE Spec 109-42, Condition A.
Apply axial load of 3 pounds to
individual contacts.
TE Spec 109-30.
gage 2.
See Figure 4.
TE Spec 109-35.
gage 1 and m easure force to
separate.
See Figure 4.
TE Spec 109-35.
Mate and unm ate pin and
receptacle connectors for 250
cycles.
TE Spec 109-27.
printed circuit boards to solder bath
at 260 ±5 C for 10 ±2 seconds.
Spec 109-63-3.
board hole.
Apply an axial load of 10 pounds for
10 seconds.
Apply 2 inch ounces for 10 seconds
in both directions.
Subject m ated connectors to 5
cycles between -65 and 125°C.
TE Spec 109-22.
Subject m ated connectors to 10
hum idity-tem perature cycles
between 25 and 65°C at 95% RH.
TE Spec 109-23, Method III,
Condition B, less steps 7 a and 7b.
Procedure
108-9063
3 of 6