HEDM-5500#J02 Avago Technologies US Inc., HEDM-5500#J02 Datasheet
HEDM-5500#J02
Specifications of HEDM-5500#J02
Available stocks
Related parts for HEDM-5500#J02
HEDM-5500#J02 Summary of contents
Page 1
... IC. The outputs of the HEDS-5500/5600 and HEDM-5500/ 5600 are two square waves in quadrature. The HEDS-5540/5640 and HEDM-5540 also have a third channel index output in addition to the two channel quadrature. This index output electrical degree, high true index pulse which is generated once for each full rotation of the codewheel ...
Page 2
... Package Dimensions HEDS-5500/5540, HEDM-5500/5540 *Note: For the HEDS-5500 and HEDM-5500, Pin # Connect. For the HEDS-5540 and HEDM-5540, Pin #2 is CH. I, the index output. HEDS-5600/5640, HEDM-5600 *Note: For the HEDS-5600 and HEDM-5600, Pin # Connect. For the HEDS-5640, Pin #2 is CH. I, the index output. ...
Page 3
... This output one state width (nominally 90 electri- cal degrees), high true index pulse which is coincident with the low states of channels A and B. Block Diagram Note: Circuitry for only for HEDS-5540, 5640 and HEDM 5540 Three Channel Encoder 3 Definitions Count (N): The number of bar and window pairs or counts per revolution (CPR) of the codewheel. One Cycle (C): 360 electrical degrees (° ...
Page 4
... RPM 30,000 RPM 2 250,000 rad/sec 250,000 rad/sec Index Pulse Width (P an index output is high during one full shaft rotation. This value is nominally 90°e or 1/4 cycle. HEDM-5540 -40°C to 85°C -40°C to 85° VCC -1 1000 Hz ± 0.175 mm (± 0.007 in.) ...
Page 5
... Plus Axial Play (HEDS Series) Shaft Eccentricity Plus Radial Play (HEDS Series) Shaft Perpendicularity Plus Axial Play (HEDM Series) Shaft Eccentricity Plus Radial Play(HEDM Series) Note: The module performance is guaranteed to 100 kHz but can operate at higher frequencies. 2.7 kΩ pull-up resistors required for HEDS- 5540/5640 and HEDM-5540 ...
Page 6
... Rise Time Fall Time HEDM-5500 Supply Current HEDM-5600 High Level Output Voltage Low Level Output Voltage Rise Time Fall Time HEDM-5540 Supply Current High Level Output Voltage Low Level Output Voltage Rise Time Fall Time * Typical values specifi 5.0V and 25º Sym ...
Page 7
... Notes: 1. These are tolerances required of the user. 2. The HEDS-55X5 and 56X5, HEDM-5505, 5605 provide an 8.9 mm (0.35 inch) diameter hole through the housing for longer motor shafts. See Ordering Information. 3. The HEDS-5540 and 5640 must be aligned using the aligning pins as specified in Figure 3, or using the alignment tool as shown in “Encoder Mounting and Assembly” ...
Page 8
... Mounting Considerations The HEDS-5540 and 5640 three channel encoders and the HEDM Series high resolution encoders must be aligned using the aligning pins as specified in Figure 3, or using the HEDS-8910 Alignment Tool as shown in Encoder Mounting and Assembly. The use of aligning pins or alignment tool is recommend- ed but not required to mount the HEDS-5500 and 5600 ...
Page 9
... Encoder Mounting and Assembly 1a. For HEDS-5500 and 5600: Mount encoder base plate onto motor. Tighten screws step 2. 1b. For HEDS-5540, 5640 and HEDM-5500, 5600, 5540 : Slip alignment tool onto motor shaft. With alignment tool in place, mount encoder baseplate onto motor as shown above. Tighten screws. Remove alignment tool ...
Page 10
... Figure 5. HEDS-8902 nd 8903 connectors Protective Silicon Cover Protective Silicon Rubber cover gives an extra protection for HEDS-5xx0 and HEDM-5xx0 family when operating in dusty environment. The protective silicon cover is installed to HEDS-5xx0 or HEDM-5xx0 prior to the connector to the encoder is installed. Part Number HEDS-8907-001 Silicon Rubber- Semi transparent-ESD Material ...
Page 11
... Encoders with Film Codewheels Mounting Type Outputs 5 - Standard Channel Channel 6 - External Mounting Ears (Included with each order of HEDM-550X/560X two channel encoders and HEDM-554X three Channel encoders) Mounting Type Outputs 5 - Standard Channel 6 - External Channel Mounting Ears (Included with each order of HEDS-554X/564X three channel encoders) ...
Page 12
... HEDM-5500 HEDM-5505 HEDM-5540 HEDM-5545 B HEDM-5600 B J HEDM-5605 B J HEDS-5500 HEDS-5505 HEDS-5540 For product information and a complete list of distributors, please go to our web site: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2009 Avago Technologies. All rights reserved. ...