PR01000101003JA500 Vishay, PR01000101003JA500 Datasheet - Page 14

• Manufacturer Part Number: PR01000101003JA500
• Description: PR01 5% A5 100K
• Manufacturer: Vishay
• Type: Metal Filmr

Specifications of PR01000101003JA500

• Power Rating(s): 1W
• Resistance: 100kohm
• Tolerance (+ Or -): 5%
• Temperature Coefficient: ±250
• Mounting Style: Through Hole
• Construction: Axial
• Operating Temp Range: -55C to 155C
• Case Style: Conformal
• Military Standard: Not Required
• Failure Rate: Not Required
• Lead Spacing (nom): Not Requiredmm
• Product Length (mm): 8mm
• Product Depth (mm): Not Requiredmm
• Product Height (mm): Not Requiredmm
• Lead Free Status / RoHS Status: Compliant

Document Number: 28729
Revision: 14-Oct-09
CLAUSE
TEST PROCEDURES AND REQUIREMENTS
4.17
4.7
4.16
4.16.2
4.16.3
4.16.4
4.20
4.22
4.19
4.23
4.23.2
4.23.3
4.23.4
4.23.5
4.23.6
4.24
4.25.1
4.8
4.6.1.1
60115-1
IEC
METHOD
60068-2-
21 (Ua1)
78 (Cab)
21 (Ub)
21 (Uc)
29 (Eb)
14 (Na)
30 (Db)
30 (Db)
20 (Ta)
13 (M)
6 (Fc)
2 (Ba)
1 (Aa)
TEST
IEC
Insulation resistance
Tensile all samples
number of samples
Climatic sequence:
Torsion other half
Low air pressure
remaining cycles
Voltage proof on
Rapid change of
Robustness of
(steady state)
(after ageing)
terminations:
(accelerated)
(accelerated)
Solderability
Solderability
Bending half
Temperature
temperature
of samples
Damp heat
Damp heat
Damp heat
Endurance
coefficient
(at 70 °C)
insulation
Vibration
1
Dry heat
Bump
TEST
st
Cold
cycle
For technical questions, contact:
Power Metal Film Leaded Resistors
Maximum voltage (DC) after 1 min; metal block
3 s; 245 °C; Solder bath method; SnAg3Cu0.5
for 3 s at 245 °C; solder bath (SnAg3Cu0.5)
acceleration 10 g; three directions; total 6 h
loaded with 0.01 P
2 s; 235 °C; Solder bath method; SnPb40
3 x 1500 bumps in three directions; 40 g
for 2 s at 235 °C; solder bath (SnPb40)
56 days; 40 °C; 90 % to 95 % RH;
during 1 min; metal block method
5 days; 55 °C; 95 % to 100 % RH
1000 h; loaded with P
Maximum voltage U
24 h; 55 °C; 90 % to 100 % RH
Between - 55 °C and + 155 °C
3 x 360° in opposite directions
Frequency 10 Hz to 500 Hz;
2 h; 8.5 kPa; 15 °C to 35 °C
8 h steam or 16 h 155 °C;
1.5 h ON and 0.5 h OFF
displacement 1.5 mm or
30 min at UCT; 5 cycles
leads immersed 6 mm:
30 min at LCT and
Load 5 N; 4 x 90°
Load 10 N; 10 s
PROCEDURE
16 h; 155 °C
2 h; - 55 °C
(3 x 2 h)
method
70
[e-mail]
(Steps: 0 V to 100 V)
RMS
70
or U
= 500 V
max.
;
No damage ΔR max.: ± (0.5 % R + 0.05 Ω)
No damage ΔR max.: ± (0.5 % R + 0.05 Ω)
Vishay BCcomponents
PR01: ΔR max.: ± (1 % R + 0.05 Ω)
PR02: ΔR max.: ± (1 % R + 0.05 Ω)
PR03: ΔR max.: ± (2 % R + 0.05 Ω)
Good tinning (≥ 95 % covered);
Good tinning (≥ 95 % covered);
ΔR max.: ± (0.5 % R + 0.05 Ω)
ΔR max.: ± (1.5 % R + 0.1 Ω)
Number of failures: < 1 x 10
Number of failures: < 1 x 10
ΔR max.: ± (3 % R + 0.1 Ω)
ΔR max.: ± (5 % R + 0.1 Ω)
No breakdown or flashover
R
REQUIREMENTS
No visual damage
R
R
ins
≤ ± 250 ppm/K
ins
ins
No damage
no damage
no damage
min.: 1000 MΩ
min.: 10
min.: 10
PR01/02/03
3
4
MΩ
MΩ
www.vishay.com
-6
-6
123