BFC233660222 Vishay, BFC233660222 Datasheet - Page 8

• Manufacturer Part Number: BFC233660222
• Description: CAPACITOR, CLASS Y2 0.0022CAPACITOR, CLASS Y2 0.0022
• Manufacturer: Vishay
• Series: 2222336r

Specifications of BFC233660222

• Capacitance: 2200pF
• Tolerance (+ Or -): 20%
• Voltage: 300VAC
• Temp Coeff (dielectric): PLYP
• Mounting Style: Through Hole
• Construction: Radial
• Failure Rate: Not Required
• Seated Plane Height: 10mm
• Product Diameter (mm): Not Requiredmm
• Product Height (mm): 10mm
• Product Depth (mm): 4mm
• Product Length (mm): 12.5mm
• Lead Spacing (nom): 10mm
• Lead Diameter (nom): 0.6mm
• Operating Temp Range: -55C to 105C
• Package / Case: Not Required
• Voltage Rating, Ac: 250V
• Voltage Rating, Dc: 630V
• Capacitor Dielectric Type: POLYPROPYLENE
• Tolerance,: 20%
• Tolerance, -: 20%
• Temp, Op.: ROHS COMPLIANT
• Lead Free Status / RoHS Status: Compliant

MKP 336 6 Y2
Vishay BCcomponents
INSPECTION REQUIREMENTS
General Notes
1. Sub-clause numbers of tests and performance requirements refer to the “ Sectional Specification, IEC-publication EN 132400
2. In this table: D = destructive
Group C inspection requirements
www.vishay.com
8
SUB - CLAUSE NUMBER
AND TEST
Group C inspection (periodic) see section “General notes“ item 3
SUB-GROUP C1A PART OF SAMPLE
OF SUB-GROUP C1
4.1 Dimensions (detail)
Initial measurements
4.3 Robustness of terminations
4.4 Resistance to soldering heat
4.19 Component solvent resistance
4.4.2 Final measurements
SUB - GROUP C1B PART OF SAMPLE
OF SUB - GROUP C1
Initial measurements
4.20 Solvent resistance of the marking:
4.6 Rapid change of temperature
4.6.1 Inspection
(IEC 60384-14) and section one of this specification”.
ND = non destructive
see Section “General notes”; item 5
For technical questions, contact:
Interference Suppression Film Capacitors
OR
ND
D
D
D
Capacitance
Tangent of loss angle at 10 kHz
Tensile: load 10 N; 10 s
Bending: load 5 N; 4 x 90°
No pre-drying
Method: 1A
Isopropylalcohol at room temperature
Method: 2
Visual examination
Capacitance
Tangent of loss angle
Insulation resistance
Capacitance
Tangent of loss angle at 10 kHz
Isopropylalcohol at room temperature
Method: 1
θA = - 55 °C
θB = + 105 °C
5 cycles
Duration t = 30 min
Solder bath: 260 °C
Duration: 10 s
Immersion time: 5 min ± 0.5 min
Recovery time:
Min. 1 h, max. 2 h
Rubbing material: cotton wool
Immersion time: 5 min ± 0.5 min
MKP Radial Potted Type
CONDITIONS
[e-mail]
As specified in chapters “General data” of
this specification
No visible damage
No visible damage
Legible marking
|DC/C| ≤ 5 % of the value measured
initially
Increase of tan δ:
Compared to values measured initially
As specified in section “Insulation
Resistance” of this specification
No visible damage
Legible marking
PERFORMANCE REQUIREMENTS
≤ 0.008
Document Number: 28115
Revision: 03-May-10