FWDM-1619-7D-51 Finisar Corporation, FWDM-1619-7D-51 Datasheet
FWDM-1619-7D-51
Specifications of FWDM-1619-7D-51
Related parts for FWDM-1619-7D-51
FWDM-1619-7D-51 Summary of contents
Page 1
... Single 3.3V power supply Operating temperature range: 0°C to 70°C Finisar’s FWDM-1619-7D-xx CWDM Small Form Factor Pluggable (SFP) transceivers are designed for operation in Metro Access Rings and Point-to-Point networks using Gigabit Ethernet and Fibre Channel networking equipment. They are available in eight different CWDM wavelengt hs ...
Page 2
... FWDM-1619-7D-xx SFP Product Specification May 2003 Wavelength xx 1470 nm 47 1490 nm 49 1510 nm 51 1530 Pin Descriptions Pin Symbol 1 V Transmitter Ground (Common with Receiver Ground) EET 2 T Transmitter Fault. Not supported. FAULT 3 T Transmitter Disable. Laser output disabled on high or open. DIS ...
Page 3
... FWDM-1619-7D-xx SFP Product Specification May 2003 VeeT 1 2 TXFault 3 TX Disable 4 MOD-DEF(2) Towards 5 MOD-DEF(1) Bezel 6 MOD-DEF(0) Rate Select 7 8 LOS 9 VeeR 10 VeeR Diagram of Host Board Connector Block Pin Numbers and Names II. Absolute Maximum Ratings Parameter Maximum Supply Voltage Storage Temperature Case Operating Temperature III ...
Page 4
... FWDM-1619-7D-xx SFP Product Specification May 2003 3. Into 100 ohms differential termination – Loss Of Signal is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected. 6. Receiver sensitivity is compliant with power supply sinusoidal modulation 1.5 MHz up to specified value applied through the recommended power supply filtering network. ...
Page 5
... FWDM-1619-7D-xx SFP Product Specification May 2003 V. General Specifications Parameter Data Rate Total System Budget VI. Environmental Specifications Finisar CWDM SFP transceivers have an operating temperature range from 0°C to +70°C case temperature. Parameter Case Operating Temperature Storage Temperature VII. Regulatory Compliance Finisar CWDM SFP transceivers are Class 1 Laser Products. They are certified per the ...
Page 6
... FWDM-1619-7D-xx SFP Product Specification May 2003 VIII. Digital Diagnostic Functions Finisar FWDM-1619-7D-xx SFP transceivers support the 2-wire serial communication protocol as defined in the draft SFP MSA defined in the GBIC standard, with the same electrical specifications. The standard SFP serial ID provides access to identification information that describes the transceiver’ ...
Page 7
... FWDM-1619-7D-xx SFP Product Specification May 2003 IX. Mechanical Specifications Finisar’s Multi-rate CWDM Small Form Factor Pluggable (SFP) transceivers are compatible with the dimensions defined by the SFP Multi-Sourcing Agreement (MSA). FWDM-1619-7D-xx (dimensions are in inches) Finisar Corporation May 2003 Rev Page 7 ...
Page 8
... FWDM-1619-7D-xx SFP Product Specification May 2003 X. PCB Layout and Bezel Recommendations Finisar Corporation May 2003 Rev Page 8 ...
Page 9
... FWDM-1619-7D-xx SFP Product Specification May 2003 Finisar Corporation May 2003 Rev Page 9 ...
Page 10
... National Standard for Information Systems. (*) Neither IEEE 802.3 nor FC-PI 10.0 specifies a 16xx nm DFB single mode interface. The FWDM-1619-7D-xx complies with these specifications except for the following optical parameters, which have different values: transmitter wavelength, receiver sensitivity, and transmit output power. See Section IV for details. ...