270T220R103B1A1 CTS Components, 270T220R103B1A1 Datasheet - Page 2

• Manufacturer Part Number: 270T220R103B1A1
• Manufacturer: CTS Components

Electrical and Mechanical Specifications
All Other Mounts
Suggested Panel for Twist Tab
Locating Lugs (Bushing Mount)
Water Seal Construction
Shaft and Bushing Information
Bushing Lengths Available
Thread Size
Molded Shafts Available
Metal Shafts Available
Standard: Twist tab (designated by “1”)
Special:
.042" thick (1.07mm)
Standard: .312" (7.9mm) radius from center of control.
Special:
Standard Position: Left side supplied unless otherwise
Other Positions:
Controls are also available to prevent water
Standard: .187" or .250" (4.75mm or 6.35mm)
Special:
Standard:
Special:
(Shown with preferred diameter bushing)
Bushing Mounted or Ear Mounted
(Shown with preferred diameter bushing)
Single or Dual Units
from entering the control through either the
O.D. of shaft and/or the bushing.
INCH
INCH
.156
.187
.236
.250
.125
.156
.187
.236
.250
SHAFT DIAMETER
SHAFT DIAMETER
Bend tab — 2 or 3 ears
Bracket mounted
.375" (9.53mm) radius from center of control.
.125" increments (3.2mm increments)
1
3
M7 x .75
M8 x .75P
As required
/
/
4
8
" – 32
" – 32
6.35
6.35
MM
MM
specified.
Available with lug right side,
without lugs, or with lugs both
left and right sides.
4.0
4.7
6.0
3.2
4.0
4.7
6.0
1/4" – 32
3/8" – 32
3/8" – 32
1/4" – 32
1/4" – 32
3/8" – 32
3/8" – 32
3/8" – 32
BUSHING DIAMETER
BUSHING DIAMETER
INCH
INCH
—
M7X.75
M7X.75
M8X.75
M9X.75
M7X.75
M7X.75
M7X.75
M8X.75
M9X.75
MM
MM
Metal
Molded
Terminal Information
(continued)
Concentric Tandem Units
Lengths: Minimum .125" (3.2mm) beyond bushing;
Trims:
Flatted and knurled with screwdriver slot available
Standard: T Solder lug formed 90° to the rear.
Special:
Available in two combinations:
Most metal shaft diameters can be used with
twist tab mountings. With bracket mount,
only .187 diameter shafts are used, with turn-down
available to obtain smaller diameters.
in many lengths and diameters.
T:
T:
U: PC terminals formed 90° forward toward
V:
W: Wire wrap terminals — .156" (4.0mm) terminal
BX: PC terminals standard .438" (11.1mm) from
X:
Y:
A – .125" (3.2mm) diameter rear shaft
B – .156" (4.0mm) diameter rear shaft
Solder lug perpendicular to shaft.
Solder lug formed 60° to the rear.
mounting surface. Terminals extend .187"
(4.7mm) beyond mounting surface.
PC terminals formed 90° to the rear, away
from panel mounting. Terminals extend .520"
(13.2mm) from mounting surface.
extension beyond base, formed 60° to the rear.
center line of control to PC board; straight
terminals extend .156" (4.0mm) into PC board.
PC terminals standard .505" (12.8mm) from
center line of control to PC board, with .136"
(3.4mm) straight terminal extension beyond
PC board standoff.
PC terminals standard .602" (15.3mm) from
centerline of control to PC board, with .140"
(3.5mm) straight terminal extension beyond
PC board standoff.
.250" (6.35mm) panel shaft
.236" (6.0mm) diameter panel shaft
special lengths as required.
Plain round screwdriver slotted, flatted,
knurled. Other trims available
upon request.
(See below)
(3/8 – 32 or M9X.75)
(3/8 – 32 or M8X.75)
(continued on next page)