CC109104642 Lineage Power, CC109104642 Datasheet
CC109104642
Specifications of CC109104642
Related parts for CC109104642
CC109104642 Summary of contents
Page 1
Data Sheet January 18, 2010 Austin MicroLynx II 8.3Vdc – 14Vdc input; 0.75Vdc to 5.5Vdc Output; 6A Output Current RoHS Compliant EZ-SEQUENCE Applications Distributed power architectures Intermediate bus voltage applications Telecommunications equipment Servers and storage applications Networking equipment Enterprise Networks ...
Page 2
Data Sheet January 18, 2010 Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or ...
Page 3
Data Sheet January 18, 2010 Electrical Specifications Parameter Output Voltage Set-point ( =25°C) IN IN, min O O, max A Output Voltage (Over all operating input voltage, resistive load, and temperature conditions until end ...
Page 4
Data Sheet January 18, 2010 Electrical Specifications Parameter Dynamic Load Response (dIo/dt=2.5A/μ IN, nom A Load Change from Io= 50% to 100% of Io,max 2x150 μF polymer capacitors Peak Deviation Settling ...
Page 5
Data Sheet January 18, 2010 Feature Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. See Feature Descriptions for additional information. Parameter On/Off Signal interface Device code with Suffix “4” – Positive logic ...
Page 6
Data Sheet January 18, 2010 Characteristic Curves The following figures provide typical characteristics for the Austin MicroLynx OUTPUT CURRENT, I Figure 1. Converter Efficiency versus Output Current (Vout ...
Page 7
Data Sheet January 18, 2010 Characteristic Curves (continued) The following figures provide typical characteristics for the MicroLynx 4.5 4 3.5 3 2.5 2 1 INPUT VOLTAGE, V Figure 7. Input voltage vs. Input ...
Page 8
Data Sheet January 18, 2010 Characteristic Curves (continued) The following figures provide typical characteristics for the Austin MicroLynx TIME, t (10μs/div) Figure 13. Transient Response to Dynamic Load Change from 100% of 50% full load (Vo = 5.0 Vdc, Cext ...
Page 9
Data Sheet January 18, 2010 Characteristic Curves (continued) The following figures provide thermal derating curves for the Austin MicroLynx 0.5m/s (100 LFM ) 3 1.0m/s (200 LFM ) 2 1.5m/s (300 LFM ) 1 2.0m/s ...
Page 10
Data Sheet January 18, 2010 8.3 – 14Vdc input; 0.75Vdc to 5.5Vdc Output; 6A output current Test Configurations TO OSCILLOSCOPE L TEST 1μ 1000μF S Electrolytic 2x100μF E.S.R.<0.1Ω Tantalum @ 20°C 100kHz NOTE: Measure input reflected ripple ...
Page 11
Data Sheet January 18, 2010 Design Considerations Output Filtering TM The Austin MicroLynx II 12V SIP module is designed for low output ripple voltage and will meet the maximum output ripple specification with 1 µF ceramic and 10 µF polymer ...
Page 12
Data Sheet January 18, 2010 Feature Description Remote On/Off TM Austin MicroLynx II 12V SIP power modules feature an On/Off pin for remote On/Off operation. Two On/Off logic options are available in the Austin TM MicroLynx II 12V series modules. ...
Page 13
Data Sheet January 18, 2010 Feature Descriptions (continued) Output Voltage Programming The output voltage of the Austin MicroLynx SIP can be programmed to any voltage from 0.75Vdc to 5.5Vdc by connecting a resistor (shown as Rtrim in Figure 30) between ...
Page 14
... When pre-bias immunity during start-up is required, the EZ-SEQUENCE must be disabled. For additional guidelines on using TM EZ-SEQUENCE feature of Austin MicroLynx 12V, contact your Lineage Power technical LINEAGE POWER TM Austin MicroLynx II 12V SIP Non-isolated Power Modules: 8.3 – 14Vdc input; 0.75Vdc to 5.5Vdc Output; 6A output current representative for preliminary application note on output voltage sequencing using Austin Lynx II series ...
Page 15
Data Sheet January 18, 2010 Thermal Considerations Thermal Considerations Power modules operate in a variety of thermal Power modules operate in a variety of thermal environments; however, sufficient cooling should be environments; however, sufficient cooling should be provided to help ...
Page 16
... For Pb solder, the recommended pot temperature is 260°C, while the Pb-free solder pot is 270°C max. Not all RoHS-compliant through-hole products can be processed with paste-through-hole Pb or Pb-free reflow process. If additional information is needed, please consult with your Lineage Power technical representative for more details. LINEAGE POWER TM ...
Page 17
Data Sheet January 18, 2010 Mechanical Outline Dimensions are in millimeters and (inches). Tolerances: x.x mm ± 0.5 mm (x.xx in. ± 0.02 in.) [unless otherwise indicated] x.xx mm ± 0.25 mm (x.xxx in ± 0.010 in.) Top View Side ...
Page 18
Data Sheet January 18, 2010 Recommended Pad Layout Dimensions are in millimeters and (inches). Tolerances: x.x mm ± 0.5 mm (x.xx in. ± 0.02 in.) [unless otherwise indicated] x.xx mm ± 0.25 mm (x.xxx in ± 0.010 in.) x.xx mm ...
Page 19
... Tel: +65 6593 7211 Europe, Middle-East and Africa Headquarters Tel: +49 898 780 672 80 India Headquarters Tel: +91 80 28411633 Efficiency Connector Comcodes 3.3V@ 6A Type 89.0% SIP 108989034 89.0% SIP CC109101763 89.0% SIP 108989042 89.0% SIP CC109104642 Document No: DS04-025 ver. 1.33 PDF name: microlynx_II_12v_sip_ds.pdf 19 ...