S602TSRP Littelfuse / Teccor Brand Thyristors, S602TSRP Datasheet - Page 4

• Manufacturer Part Number: S602TSRP
• Description: SCR SENS 600V 1.5A SOT223 T/R
• Manufacturer: Littelfuse / Teccor Brand Thyristors

Specifications of S602TSRP

• Scr Type: Sensitive Gate
• Voltage - Off State: 600V
• Voltage - Gate Trigger (vgt) (max): 800mV
• Voltage - On State (vtm) (max): 1.7V
• Current - On State (it (av)) (max): 950mA
• Current - On State (it (rms)) (max): 1.5A
• Current - Gate Trigger (igt) (max): 200µA
• Current - Hold (ih) (max): 5mA
• Current - Off State (max): 5µA
• Current - Non Rep. Surge 50, 60hz (itsm): 12.5A, 15A
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: SOT-223 (3 leads + Tab), SC-73, TO-261
• Current - On State (it (rms) (max): 1.5A
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: S602TS; S602TSRP; S602TSRPTR

Sx02xS Series
Figure 6: Surge Peak On-State Current vs. Number of Cycles
Soldering Parameters
Reflow Condition
Pre Heat
Average ramp up rate (Liquidus Temp)
(T
T
Reflow
Peak Temperature (T
Time within 5°C of actual peak
Temperature (t
Ramp-down Rate
Time 25°C to peak Temperature (T
Do not exceed
S(max)
L
) to peak
15
12
10
20
to T
9
8
7
6
5
3
2
1
4
1
L
- Ramp-up Rate
- Temperature Min (T
- Temperature Max (T
- Time (min to max) (t
- Temperature (T
- Time (min to max) (t
2
p
)
3
P
4
)
5 6 7 8 9 10
Surge Current Duration – Full Cycle
L
) (Liquidus)
s(min)
s(max)
s
s
)
)
P
)
EV Series 1.5 Amp Sensitive SCRs
20
Teccor
)
)
30 40
Pb – Free assembly
150°C
200°C
60 – 180 secs
5°C/second max
5°C/second max
217°C
60 – 150 seconds
260
20 – 40 seconds
5°C/second max
8 minutes Max.
280°C
Revised: December 22, 2010 09:54 AM
60 80 100
+0/-5
®
brand Thyristors
°C
204
200
300 400 600
1000
T
T
S(max)
S(min)
25
T
T
Please refer to http://www.littelfuse.com for current information.
P
L
time to peak temperature
Supply Frequency: 60Hz Sinusoidal
Load: Resistive
RMS On-State Current [I
Specific Case Temperature
Notes:
1. Gate control may be lost during and immediately
following surge current interval.
2. Overload may not be repeated until junction
temperature has returned to steady-state rated value.
Specifications are subject to change without notice.
t
S
Preheat
Preheat
Ramp-up
Ramp-up
T(RMS)
]: Max Rated Value at
©2011 Littelfuse, Inc
t
t
P
L
Ramp-down
Ramp-do
Time