ADSP-BF533SBBC500 Analog Devices Inc, ADSP-BF533SBBC500 Datasheet - Page 10

• Manufacturer Part Number: ADSP-BF533SBBC500
• Description: DSP Fixed-Point 16-Bit 500MHz 500MIPS 160-Pin CSP-BGA
• Manufacturer: Analog Devices Inc
• Series: Blackfin®r
• Type: Fixed Pointr

Specifications of ADSP-BF533SBBC500

• Package: 160CSP-BGA
• Numeric And Arithmetic Format: Fixed-Point
• Maximum Speed: 500 MHz
• Device Million Instructions Per Second: 500 MIPS
• Rohs Status: RoHS non-compliant
• Interface: SPI, SSP, UART
• Clock Rate: 500MHz
• Non-volatile Memory: ROM (1 kB)
• On-chip Ram: 148kB
• Voltage - I/o: 1.8V, 2.5V, 3.3V
• Voltage - Core: 1.20V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 160-CSPBGA
• For Use With: ADZS-BFAUDIO-EZEXT - BOARD EVAL AUDIO BLACKFINADZS-BFAV-EZEXT - BOARD DAUGHT ADSP-BF533,37,61KITADZS-BF533-EZLITE - KIT W/BOARD EVAL FOR ADSP-BF533

ADSP-BF531/BF532/BF533
13.
14.
DESCRIPTION:
Consider the following scenario:
In this case, an erroneous interrupt will occur, even though no edge was physically present at the input. This will also occur at any
subsequent writes of a 1 to this bit of the polarity register. If the polarity register is reset to 0, no interrupt is generated, as expected.
In the opposite case, with the external pin level equal to 1, the erroneous interrupt is generated when the polarity bit is changed from 1 to
0 (and any subsequent writes of a 1 to this bit of the polarity register), and not when changed from 0 to 1.
In the case of multiple I/O pins configured as edge-sensitive interrupts, ANY change to the polarity register will affect all those I/O pins in
the above manner. The workaround in this case needs to be applied to all of those pins.
Similar considerations apply to the input enable register. Changing this setting while edge-sensitive interrupts are enabled will also cause
unwanted interrupts.
WORKAROUND:
Prior to changing the polarity (and/or input enable) register(s), disable the interrupts (i.e., by clearing the PFA or PFB IMASK bit), change
the register setting, clear the interrupt request as you normally would (write to the data or clear registers), and then re-enable the
interrupt again.
APPLIES TO REVISION(S):
0.3
DESCRIPTION:
When using internal SPORT clocks or external SPORT clocks with falling edge selected (SPORTx_TCR1:TCKE, SPORTx_RCR1:RCKE), if the
SPORT is disabled and then subsequently re-enabled, there is a possibility of corrupting the first word transmitted or received.
WORKAROUND:
For internal SPORT clocks:
After disabling the SPORT, write bit 1 of the SPORT configuration 1 register (SPORTx_TCR1:ITCLK, SPORTx_RCR1:IRCLK) to 0. This will
switch the SPORT clock to external, allowing the SPORT to be fully reset.
For external SPORT clocks with falling edge selected:
After disabling the SPORT, write bit 14 of the SPORT configuration 1 register (SPORTx_TCR1:TCKE, SPORTx_RCR1:RCKE) to 0. This will allow
the SPORT to be fully reset.
APPLIES TO REVISION(S):
0.3
05000193 - False I/O Pin Interrupts on Edge-Sensitive Inputs When Polarity Setting Is Changed:
05000194 - Restarting SPORT in Specific Modes May Cause Data Corruption:
1) Pins are configured as edge-sensitive inputs.
2) The interrupt occurs on the rising edge.
3) Input level is constant and 0.
4) Change the polarity setting to set the interrupt to occur on the falling edge instead.
NR003532D | Page 10 of 45 | July 2008
Silicon Anomaly List