BFC246804106 Vishay, BFC246804106 Datasheet - Page 23

• Manufacturer Part Number: BFC246804106
• Description: Cap Film 10uF 100VDC/63VAC PET 10% 26 X 10.5 X 23.5mm RDL 22.5mm Loose in Box
• Manufacturer: Vishay
• Series: 2222468r

Specifications of BFC246804106

• Package/case: 26(Max) X 10.5(Max) X 23.5(Max)
• Mounting: Through Hole
• Capacitance Value: 10 uF
• Voltage: 100|63 Vdc|Vac
• Dielectric: PET
• Lead Pitch For Radial: 22.5 mm
• Product Length: 26(Max) mm
• Product Depth: 10.5(Max) mm
• Tolerance: 10 %
• Operating Temperature: -55 to 105 °C
• Capacitance: 10UF
• Voltage Rating, Ac: 63V
• Voltage Rating, Dc: 100V
• Capacitor Dielectric Type: POLYESTER
• Tolerance,: 10%
• Tolerance, -: 10%
• Temp, Op. Max: 85(DEGREE C)
• Temp,: ROHS COMPLIANT

3. The voltage pulse slope (dU/dt) shall not exceed the rated voltage pulse slope in an RC-circuit at rated voltage and without
4. The maximum component surface temperature rise must be lower than the limits (see graph max. allowed component
5. Since in circuits used at voltages over 280 V peak-to-peak the risk for an intrinsically active flammability after a capacitor
6. When using these capacitors as across-the-line capacitor in the input filter for mains applications or as series connected with
Voltage Conditions for 6 Above
EXAMPLE
C = 330 nF - 100 V used for the voltage signal shown in next drawing.
U
The ambient temperature is 35 °C
Checking conditions:
1. The peak voltage U
2. The peak-to-peak voltage 80 V is lower than 2 2 x 63 V
3. The voltage pulse slope (dU/dt) = 80 V/500 µs = 0.16 V/µs
4. The dissipated power is 60 mW as calculated with fourier terms
5. Not applicable
6. Not applicable
Voltage Signal
Document Number: 28105
Revision: 22-Dec-10
P-P
ALLOWED VOLTAGES
Maximum continuous RMS voltage
Maximum temperature RMS-overvoltage (< 24 h)
Maximum peak voltage (V
ringing. If the pulse voltage is lower than the rated DC voltage, the rated voltage pulse slope may be multiplied by U
divided by the applied voltage.
For all other pulses following equation must be fulfilled:
T is the pulse duration.
The rated voltage pulse slope is valid for ambient temperatures up to 85 °C. For higher temperatures a derating factor of 3 %
per K shall be applied.
temperature rise).
breakdown (short circuit) increases, it is recommended that the power to the component is limited to 100 times the values
mentioned in the table: “Heat Conductivity”
an impedance to the mains the applicant must guarantee that the following conditions are fulfilled in any case (spikes and
surge voltages from the mains included).
This is lower than 20 V/µs (see specific reference data for each version)
The temperature rise for W
This is lower than 15 °C temperature rise at 35 °C, according figure “Max. allowed component temperature rise”
= 80 V; U
2
T

0


dU
------- -
P
dt
= 70 V; T


2
dt
P
Voltage
U
O-P
= 70 V is lower than 100 V
1
Rdc
= 0.5 ms; T
U
) (< 2 s)
P
max.


dU
------- -
dt
= 8.5 mm and pitch = 15 mm will be 60 mW/11 mW/°C = 5.5 °C


rated
2
T
= 1 ms
1
For technical questions, contact:
MKT Radial Lacquered Type
T
2
DC Film Capacitors
DC
U
P-P
AC
= 178 U
T
1.25 x U
1.6 x U
amb
P-P
U
[e-mail]
RAC
85 °C
MKT467, MKT468, MKT469
RAC
RAC
Vishay BCcomponents
Time
85 °C < T
0.8 x U
1.3 x U
U
amb
RAC
RAC
RAC
www.vishay.com
105 °C
RDC
and
73