CE UMK107 B7104KA-T Taiyo Yuden, CE UMK107 B7104KA-T Datasheet - Page 51

• Manufacturer Part Number: CE UMK107 B7104KA-T
• Description: Cap Ceramic 0.1uF 50VDC X7R 10% SMD 0603 T/R
• Manufacturer: Taiyo Yuden
• Type: Flatr

Specifications of CE UMK107 B7104KA-T

• Package/case: 0603
• Mounting: Surface Mount
• Capacitance Value: 0.1 uF
• Dielectric: X7R
• Voltage: 50 Vdc
• Product Length: 1.6 mm
• Product Height: 0.8 mm
• Tolerance: 10 %

■
Precautions on the use of Multilayer Ceramic Capacitors
※RCR-2335B （Safety Application Guide for fixed ceramic capacitors for use in electronic equipment） is published by JEITA.
Please check the guide regarding precautions for deflection test, soldering by spot heat, and so on.
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
mlcc_prec_e-01
5. Cleaning
6. Resin coating and mold
7. Handling
8. Storage conditions
Precautions
Precautions
Precautions
Precautions
consider-
consider-
Technical
Technical
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
PRECAUTIONS
ations
ations
◆Cleaning conditions
◆Splitting of PCB
◆Mechanical considerations
◆Storage
If capacitors are stored in a high temperature and humidity environment, it might rapidly cause poor solderability due to terminal oxidation and quality loss of taping/
packaging materials. For this reason, capacitors shall be used within 6 months from the time of delivery. If exceeding the above period, please check solderability be-
fore using the capacitors.
1. When PCBs are cleaned after capacitors mounting, please select the appropriate cleaning solution in accordance with the intended use of the cleaning. （e.g. to
2. Cleaning condition shall be determined after it is verified by using actual cleaning machine that the cleaning process does not affect capacitor's characteristics.
1. The use of inappropriate cleaning solutions can cause foreign substances such as flux residue to adhere to capacitors or deteriorate their outer coating, resulting in
2. Inappropriate cleaning conditions （insufficient or excessive cleaning） may adversely affect the performance of the capacitors.
1. With some type of resins, decomposition gas or chemical reaction vapor may remain inside the resin during the hardening period or while left under normal stor-
2. When a resin's hardening temperature is higher than capacitor's operating temperature, the stresses generated by the excessive heat may lead to damage or
1. When PCBs are split after components mounting, care shall be taken so as not to give any stresses of deflection or twisting to the board.
2. Board separation shall not be done manually, but by using the appropriate devices.
Be careful not to subject capacitors to excessive mechanical shocks.
1. To maintain the solderability of terminal electrodes and to keep packaging materials in good condition, care must be taken to control temperature and humidity in
2. The capacitance values of high dielectric constant capacitors will gradually decrease with the passage of time, ｓ o care shall be taken to design circuits . Even if
（1） If ceramic capacitors are dropped onto a floor or a hard surface, they shall not be used.
（2） Please be careful that the mounted components do not come in contact with or bump against other boards or components.
・Recommended conditions
・Ceramic chip capacitors shall be kept where no chlorine or sulfur exists in the air.
the storage area. Humidity should especially be kept as low as possible.
capacitance value decreases as time passes, it will get back to the initial value by a heat treatment at 150℃ for 1hour.
age conditions resulting in the deterioration of the capacitor's performance.
destruction of capacitors.
The use of such resins, molding materials etc. is not recommended.
remove soldering flux or other materials from the production process.）
a degradation of the capacitor's electrical properties （especially insulation resistance） .
In the case of ultrasonic cleaning, too much power output can cause excessive vibration of PCBs which may lead to the cracking of capacitors or the soldered
portion, or decrease the terminal electrodes' strength. Therefore, the following conditions shall be carefully checked;
tors shall be used within 6 months from the time of delivery.
The ambient temperature must be kept below 40℃. Even under ideal storage conditions, solderability of capacitor is deteriorated as time passes, so capaci-
Ultrasonic output : 20 W/ℓ or less
Ultrasonic frequency : 40 kHz or less
Ultrasonic washing period : 5 min. or less
Ambient temperature
Humidity
: Below 30℃
: Below 70% RH
1 1
mlcc_prec-P4