GRM1885C1H2R2CZ01D Murata, GRM1885C1H2R2CZ01D Datasheet - Page 12
![CAPACITOR, 0603 2.2PF 50V CAPACITOR, 0603 2.2PF 50V](/photos/30/39/303926/grm_sml.jpg)
GRM1885C1H2R2CZ01D
Manufacturer Part Number
GRM1885C1H2R2CZ01D
Description
CAPACITOR, 0603 2.2PF 50V CAPACITOR, 0603 2.2PF 50V
Manufacturer
Murata
Series
GRM18r
Specifications of GRM1885C1H2R2CZ01D
Tolerance (+ Or -)
0.25pF
Voltage
50VDC
Temp Coeff (dielectric)
C0G
Operating Temp Range
-55C to 125C
Mounting Style
Surface Mount
Construction
SMT Chip
Case Style
Ceramic Chip
Failure Rate
Not Required
Wire Form
Not Required
Product Length (mm)
1.6mm
Product Depth (mm)
0.8mm
Product Height (mm)
0.8mm
Product Diameter (mm)
Not Requiredmm
Capacitance
2.2pF
Package / Case
0603
Voltage Rating, Dc
50V
Capacitor Dielectric Type
CERAMIC MULTI-LAYER
Tolerance,
11%
Tolerance, -
11%
Temp, Op. Max
125(DEGREE C)
Temp, Op.
ROHS COMPLIANT
Lead Free Status / RoHS Status
Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
GRM1885C1H2R2CZ01D
Manufacturer:
MURATA
Quantity:
24 000
!Note
!Note
No.
16
17
Continued from the preceding page.
Humidity
Steady
State
Humidity
Load
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
Item
Appearance
Capacitance
Change
Q/D.F.
I.R.
Dielectric
Strength
Appearance
Capacitance
Change
Q/D.F.
I.R.
Dielectric
Strength
The measured and observed characteristics should satisfy the
specifications in the following table.
No marking defects
Within T5% or T0.5pF
(Whichever is larger)
30pF and over : QU350
10pF and over
30pF and below :
More than 1,000MΩ or 50Ω • F (Whichever is smaller)
No failure
The measured and observed characteristics should satisfy the
specifications in the following table.
No marking defects
Within T7.5% or T0.75pF
(Whichever is larger)
30pF and over : QU200
30pF and below :
More than 500MΩ or 25Ω • F (Whichever is smaller)
No failure
10pF and below :
C : Nominal Capacitance (pF)
C : Nominal Capacitance (pF)
Compensating Type
QU275W5C/2
QU200W10C
QU100+10C/3
Temperature
Specifications
R6, R7 : Within T12.5%
E4, F5 : Within T30%
[R6, R7]
W.V. : 25Vmin. : 0.05max.
W.V. : 16/10V : 0.05max.
W.V. : 6.3V
[E4]
W.V. : 25Vmin. : 0.05max.
[F5]
W.V. : 25Vmin.
W.V. : 16V/10V : 0.15max.
W.V. : 6.3Vmax. : 0.2max.
R6, R7 : Within T12.5%
E4 : Within T30%
F5 : Within T30%
[W.V. : 10Vmax.]
F5 : Within W30/Y40%
[R6, R7]
W.V. : 25Vmin. : 0.05max.
W.V. : 16/10V : 0.05max.
W.V. : 6.3V
[E4]
W.V. : 25Vmin. : 0.05max.
[F5]
W.V. : 25Vmin.
W.V. : 16V/10V : 0.15max.
W.V. : 6.3Vmax. : 0.2max.
High Dielectric Type
0.075max. (CF3.3µF)
0.125max. (CU3.3µF)
0.075max. (CF3.3µF)
0.125max. (CU3.3µF)
: 0.075max. (CF0.10µF)
: 0.125max. (CU0.10µF)
: 0.075max. (CF0.10µF)
: 0.125max. (CU0.10µF)
GRM Series Specifications and Test Methods
Let the capacitor sit at 40T2D and 90 to 95% humidity for
500T12 hours.
Remove and let sit for 24T2 hours (temperature compensating
type) or 48T4 hours (high dielectric constant type) at room tem-
perature, then measure.
Apply the rated voltage at 40T2D and 90 to 95% humidity for
500T12 hours. Remove and let sit for 24T2 hours (temperature
compensating type) or 48T4 hours (high dielectric constant
type) at room temperature, then measure. The charge/discharge
current is less than 50mA.
#Initial measurement for F5/10V max.
Apply the rated DC voltage for 1 hour at 40T2D.
Remove and let sit for 48T4 hours at room temperature.
Perform initial measurement.
Test Method
Continued on the following page.
C02E10.pdf 04.1.20
25
4