COM20020I3V-HD SMSC, COM20020I3V-HD Datasheet - Page 40

• Manufacturer Part Number: COM20020I3V-HD
• Description: Network Controller & Processor ICs ARCNET Contrllr
• Manufacturer: SMSC

Specifications of COM20020I3V-HD

• Product: Controller Area Network (CAN)
• Number Of Transceivers: 1
• Data Rate: 5 Mbps
• Supply Voltage (max): 3.465 V
• Supply Voltage (min): 3.135 V
• Supply Current (max): 35 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Package / Case: TQFP-48
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

6.4
The Command Chaining operation allows consecutive transmissions and receptions to occur without host microcontroller
intervention.
Through the use of a dual two-level FIFO, commands to be transmitted and received, as well as the status bits, are
pipelined.
In order for the COM20020I 3V to be compatible with previous SMSC ARCNET device drivers, the device defaults to the
non-chaining mode. In order to take advantage of the Command Chaining operation, the Command Chaining Mode must
be enabled via a logic "1" on bit 6 of the Configuration Register.
In Command Chaining, the Status Register appears as in Figure 10.
The following is a list of Command Chaining guidelines for the software programmer. Further detail can be found in the
Transmit Command Chaining and Receive Command Chaining sections.
Transmit Command Chaining
When the processor issues the first "Enable Transmit to Page fnn" command, the COM20020I 3V responds in the usual
manner by resetting the TA and TMA bits to prepare for the transmission from the specified page. The TA bit can be
used to see if there is currently a transmission pending, but the TA bit is really meant to be used in the non-chaining mode
only. The TTA bits provide the relevant information for the device in the Command Chaining mode.
In the Command Chaining Mode, at any time after the first command is issued, the processor can issue a second "Enable
Transmit from Page fnn" command. The COM20020I 3V stores the fact that the second transmit command was issued,
along with the page number.
After the first transmission is completed, the COM20020I 3V updates the Status Register by setting the TTA bit, which
generates an interrupt. The interrupt service routine should read the Status Register. At this point, the TTA bit will be
found to be a logic "1" and the TMA (Transmit Message Acknowledge) bit will tell the processor whether the transmission
was successful. After reading the Status Register, the "Clear Transmit Interrupt" command is issued, thus resetting the
TTA bit and clearing the interrupt. Note that only the "Clear Transmit Interrupt" command will clear the TTA bit and the
interrupt. It is not necessary, however, to clear the bit or the interrupt right away because the status of the transmit
SMSC COM20020I 3.3V Rev.E
5Mbps ARCNET (ANSI 878.1) Controller with 2K x 8 On-Chip RAM
The device is designed such that the interrupt service routine latency does not affect performance.
Up to two outstanding transmissions and two outstanding receptions can be pending at any given time. The
commands may be given in any order.
Up to two outstanding transmit interrupts and two outstanding receive interrupts are stored by the device, along with
their respective status bits.
The Interrupt Mask bits act on TTA (Rising Transition on Transmitter Available) for transmit operations and TRI
(Rising Transition of Receiver Inhibited) for receive operations.
transmission only. TRI is set upon completion of a packet reception only. Typically there is no need to mask the TTA
and TRI bits after clearing the interrupt.
The traditional TA and RI bits are still available to reflect the present status of the device.
Command Chaining
TRI
TRI
MSB
RI
Figure 10 - Command Chaining Status Register Queue
TA
DATASHEET
POR
Page 40
TEST
RECON
TTA is set upon completion of a packet
TMA
TMA
TTA
TTA
Revision 09-11-06
LSB