MAX3054ASD Maxim Integrated Products, MAX3054ASD Datasheet - Page 11
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
MAX3054ASD
Manufacturer Part Number
MAX3054ASD
Description
Network Controller & Processor ICs +/-80V, 250kbps Faul t-Protected - Fault
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX3055ASD.pdf
(18 pages)
Specifications of MAX3054ASD
Product
Controller Area Network (CAN)
Number Of Transceivers
1
Data Rate
250 Kbps
Supply Voltage (max)
5.25 V, 42 V
Supply Voltage (min)
4.75 V, 5 V
Supply Current (max)
0.125 mA, 30 mA
Maximum Operating Temperature
+ 125 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Package / Case
SOIC-14
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MAX3054ASD+
Manufacturer:
Maxim
Quantity:
2 198
Company:
Part Number:
MAX3054ASD+T
Manufacturer:
MAXIM
Quantity:
2
The MAX3054/MAX3055/MAX3056 interface between
the protocol controller and the physical wires of the bus
lines in a CAN. The devices provide differential transmit
capability and switch to single-wire mode if certain fault
conditions occur (see the Failure Management section).
The MAX3054/MAX3055/MAX3056 guarantee full wake-
up capability during failure modes.
The extended fault-protection range of CANH and
CANL bus lines (±80V) allows for use in 42V automotive
applications. A current-limiting circuit protects the
transmitter output stage against overcurrent faults. This
feature prevents destruction of the transmitter output
stage. If the junction temperature exceeds a value of
approximately +165°C, the transmitter output stages
are disabled. The CANH and CANL lines are also pro-
tected against electrical transients, which can occur in
an automotive environment.
The transceiver provides three low-power modes that
can be entered and exited through pins STB and EN.
An output INH pin can be used for deactivation of an
external voltage regulator.
The MAX3054/MAX3055/MAX3056 are designed to
provide optimal operation for a specified data rate. The
PIN
10
11
12
13
14
1
2
3
4
5
6
7
8
9
NAME
WAKE
CANH
CANL
BATT
GND
RXD
ERR
RTH
TXD
STB
RTL
V
INH
______________________________________________________________________________________
EN
CC
Detailed Description
Inhibit Output. Inhibit output is for switching an external voltage regulator if a wake-up signal occurs.
Transmit Data Input
Receive Data Output
Error. Wake-up and power-on indication output; active low in normal operating mode when the bus
has a failure and in low-power modes (wake-up signal or power-on standby).
Standby. The digital control signal input (active low) defines, together with input signal on pin EN, the
state of the transceiver (in normal and low-power modes).
Enable. The digital control signal input defines, together with input signal on pin STB, the state of the
transceiver (in normal and low-power modes).
Wake-Up. Local wake-up signal input; falling and rising edges are both detected.
Termination Resistor. Termination resistor connection for CANH bus.
Termination Resistor. Termination resistor connection for CANL bus.
Supply Voltage. Bypass to ground with a 0.1µF capacitor.
High-Level Voltage Bus Line
Low-Level Voltage Bus Line
Ground
Battery Supply. Bypass to ground with a 0.1µF capacitor.
Transceivers for In-Car Applications
±80V Fault-Protected/Tolerant CAN
MAX3054 is ideal for high data rates of 250kbps. The
MAX3055 is used for data rates of 125kbps, and the
MAX3056 is designed for 40kbps applications. For the
40kbps and 125kbps versions, the built-in slope-control
feature allows the use of unshielded cables and receiver
input filters guarantee high noise immunity.
The transmitter converts a single-ended input (TXD)
from the CAN controller to differential outputs for the
bus lines (CANH, CANL).
The receiver takes differential input from the bus lines
(CANH, CANL) and converts this data as a single-
ended output (RXD) to the CAN controller. It consists of
a comparator that senses the difference ∆V = (CANH -
CANL) with respect to an internal threshold.
The main function of BATT is to supply power to the
device when vehicle battery voltage is supplied.
BATT can handle up to +80V making it ideal for 42V
automotive systems allowing power-up of the device
when the ignition is turned on.
FUNCTION
Normal Operation Mode
Pin Description
Transmitter
Receiver
BATT
11