DS32506DK Maxim Integrated Products, DS32506DK Datasheet - Page 18
DS32506DK
Manufacturer Part Number
DS32506DK
Description
Network Controller & Processor ICs 6-/8-/12-Port DS3/E3 ort DS3/E3/STS-1 LIU
Manufacturer
Maxim Integrated Products
Datasheet
1.DS32506N.pdf
(130 pages)
Specifications of DS32506DK
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 18 of 130
- Download datasheet (2Mb)
Table 7-4. Global Pin Descriptions
IFSEL[2:0]
RESREF
NAME
TEST
RST
HW
HIZ
TYPE
Ipd
Ipu
Oa
I
I
I
Microprocessor Interface Select. When no microprocessor interface is selected, all
microprocessor interface inputs are ignored and internally pulled low, and all microprocessor
interface outputs are put in a high-impedance state. See Section
000 = no microprocessor interface (must set
001 = reserved
010 = SPI serial interface, address and data MSB first
011 = SPI serial interface, address and data LSB first
100 = 8-bit parallel interface, Intel style (CS, RD,
101 = 8-bit parallel interface, Motorola style (CS,
110 = 16-bit parallel interface, Intel style (CS, RD,
111 = 16- bit parallel interface, Motorola style (CS,
Hardware Interface Enable. When the hardware interface pins are disabled, all hardware
control inputs are ignored and internally pulled low, and all hardware status outputs are put in a
high impedance state. See Section
0 = Hardware interface pins disabled
1 = Hardware interface pins enabled
Factory Test Enable (Active Low). This pin enables the internal scan test mode when low.
For normal operation tie high. This is an asynchronous input.
High-Impedance Test Enable (Active Low). This signal is used to enable testing. When this
signal is low while
high-impedance state. For normal operation this signal is high. This is an asynchronous input.
Reset (Active Low, Open Drain). When this global asynchronous reset is pulled low, all
internal circuitry is reset and all internal registers are forced to their default values. The device
is held in reset as long as
cycles. See Section 8.11.
Reference Resistor. This pin is tied to VSS through a 10kΩ ±1% resistor. This accurate
resistor is used to calibrate on-chip resistor values including internal transmit and receive
termination resistors.
JTRST
is low, all the digital output and bidirectional pins are placed in the
RST
18 of 130
is low.
6
for details.
RST
FUNCTION
should be held low for at least two reference clock
HW
WR
R/W
= 1 and use hardware interface)
WR
R/W
control signals)
,
control signals)
DS
,
DS
control signals)
control signals)
DS32506/DS32508/DS32512
6
for details.
Related parts for DS32506DK
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
IC FRAMER DS3/E3 SNGL 144CSBGA
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
IC 8CH DS3/3 FRAMER 349-BGA
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
IC 8CH DS3/3 FRAMER 349-BGA
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
IC 12CH DS3/3 FRAMER 349-BGA
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
IC 12CH DS3/3 FRAMER 349-BGA
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN 16/A°/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products