CY28442ZXC-2T Silicon Laboratories Inc, CY28442ZXC-2T Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_sml.jpg)
CY28442ZXC-2T
Manufacturer Part Number
CY28442ZXC-2T
Description
Clock Generators & Support Products Calistoga
Manufacturer
Silicon Laboratories Inc
Datasheet
1.CY28442ZXC-2.pdf
(19 pages)
Specifications of CY28442ZXC-2T
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
CY28442ZXC-2T
Manufacturer:
TI
Quantity:
11
Rev 1.0, November 21, 2006
CLK_REQ[A:B]# Assertion (CLKREQ# -> LOW)
All differential outputs that were stopped are to resume normal
operation in a glitch-free manner. The maximum latency from
the assertion to active outputs is between 2 and 6 SRC clock
periods (2 clocks are shown) with all SRC outputs resuming
simultaneously. All stopped SRC outputs must be driven high
within 10 ns of CLKREQ#[1:0] deassertion to a voltage greater
than 200 mV.
CLK_REQ[A:B]# Deassertion (CLKREQ# -> HIGH)
The impact of deasserting the CLKREQ#[A:B] pins is that all
SRC outputs that are set in the control registers to stoppable
via deassertion of CLKREQ#[A:B] are to be stopped after their
next transition. The final state of all stopped DIF signals is
LOW, both SRCT clock and SRCC clock outputs will not be
driven.
PD (Power-down) Clarification
The VTT_PWRGD# /PD pin is a dual-function pin. During
initial power-up, the pin functions as VTT_PWRGD#. Once
VTT_PWRGD# has been sampled LOW by the clock chip, the
pin assumes PD functionality. The PD pin is an asynchronous
active HIGH input used to shut off all clocks cleanly prior to
shutting off power to the device. This signal is synchronized
SRCC(free running)
SRCT(free running)
SRCT(stoppable)
SRCT(stoppable)
CPUC, 133MHz
CPUT, 133MHz
CLKREQ#X
SRCC 100MHz
SRCT 100MHz
PCI, 33 MHz
USB, 48MHz
DOT96C
DOT96T
REF
PD
Figure 3. CLK_REQ#[A:B] Deassertion/Assertion Waveform
Figure 4. Power-down Assertion Timing Waveform
internal to the device prior to powering down the clock synthe-
sizer. PD is also an asynchronous input for powering up the
system. When PD is asserted HIGH, all clocks need to be
driven to a LOW value and held prior to turning off the VCOs
and the crystal oscillator.
PD (Power-down) Assertion
When PD is sampled HIGH by two consecutive rising edges
of CPUC, all single-ended outputs will be held LOW on their
next HIGH-to-LOW transition and differential clocks must held
high or tri-stated (depending on the state of the control register
drive mode bit) on the next diff clock# HIGH-to-LOW transition
within 4 clock periods. When the SMBus PD drive mode bit
corresponding to the differential (CPU, SRC, and DOT) clock
output of interest is programmed to ‘0’, the clock output are
held with “Diff clock” pin driven HIGH at 2 x Iref, and “Diff
clock#” tri-state. If the control register PD drive mode bit corre-
sponding to the output of interest is programmed to “1”, then
both the “Diff clock” and the “Diff clock#” are tri-state. Note the
example below shows CPUT = 133 MHz and PD drive mode
= ‘1’ for all differential outputs. This diagram and description is
applicable to valid CPU frequencies 100, 133, 166, 200, 266,
333, and 400 MHz. In the event that PD mode is desired as
the initial power-on state, PD must be asserted HIGH in less
than 10 μs after asserting Vtt_PwrGd#.
CY28442-2
Page 10 of 19