NBB 8-18GM60-A2-V1 PEPPERL & FUCHS, NBB 8-18GM60-A2-V1 Datasheet - Page 2
![no-image](/images/manufacturer_photos/0/5/520/pepperl___fuchs_sml.jpg)
NBB 8-18GM60-A2-V1
Manufacturer Part Number
NBB 8-18GM60-A2-V1
Description
Inductive Sensors - DC
Manufacturer
PEPPERL & FUCHS
Datasheet
1.NBB_8-18GM60-A2-V1.pdf
(3 pages)
Specifications of NBB 8-18GM60-A2-V1
Rohs Compliant
Yes
Sensor Input
Inductive
Sensing Range
0mm To 6.48mm
Supply Voltage Range Dc
10V To 30V
2
ATEX 3G (nA)
Instruction
Device category 3G (nA)
Directive conformity
Standard conformity
CE symbol
Ex-identification
General
Installation, Comissioning
Maintenance
Special conditions
Maximum operating current I
Maximum operating voltage U
Maximum permissible ambient tempera-
ture T
Plug connector
Protection from mechanical danger
Protection from UV light
Electrostatic charging
Inductive sensor
at U
at U
at U
Umax
Subject to modifications without notice
Pepperl+Fuchs Group
www.pepperl-fuchs.com
Bmax
Bmax
Bmax
=30 V, I
=30 V, I
=30 V, I
L
L
L
=200 mA
=100 mA
=50 mA
L
Bmax
fa-info@us.pepperl-fuchs.com
USA: +1 330 486 0001
Manual electrical apparatus for hazardous areas
for use in hazardous areas with gas, vapour and mist
94/9/EG
EN 60079-0:2006, EN 60079-15:2005
Ignition protection category "n"
Use is restricted to the following stated conditions
¬ II 3G Ex nA IIC T6 X
The Ex-significant identification is on the enclosed adhesive label
The apparatus has to be operated according to the appropriate data in the data sheet and in this instruction manual.
The data stated in the data sheet are restricted by this operating instruction! The special conditions must be observed!
Laws and/or regulations and standards governing the use or intended usage goal must be observed.
The adhesive label provided must be affixed in the immediate vicinity of the sensor! The surface to which the label is applied
must be clean, flat and free from grease!
The affixed adhesive label must be readable and durable, taking account of the possibility of chemical corrosion!
No changes can be made to apparatus, which are operated in hazardous areas.
Repairs to these apparatus are not possible.
The maximum permissible load current must be restricted to the values given in the following list. High load currents and load
short-circuits are not permitted.
The maximum permissible operating voltage UB max is restricted to the values in the following list. Tolerances are not per-
missible.
dependant of the load current I
Information can be taken from the following list.
45 °C (113 °F)
50 °C (122 °F)
50 °C (122 °F)
The plug connector must not be disconnected under voltage. The proximity switch is marked as follows: “DO NOT DISCON-
NECT UNDER VOLTAGE!” When the plug connector is disconnected the ingress of dirt into the inner areas (i.e. the areas,
which are not accessible in the plugged-in condition) must be prevented.
The sensor must not be exposed to ANY FORM of mechanical danger.
The sensor and the connection cable must be protected from damaging UV-radiation. This can be achieved when the sensor
is used in internal areas.
Electrostatic charges must be avoided on the mechanical housing components. Dangerous electrostatic charges on the
mechanical housing components can be avoided by incorporating these in the equipotential bonding.
Germany: +49 621 776-4411
fa-info@pepperl-fuchs.com
L
and the max. operating voltage U
fa-info@sg.pepperl-fuchs.com
Singapore: +65 6779 9091
Copyright Pepperl+Fuchs
Bmax.
NBB8-18GM60-A2-V1-3G-3D