XS2R-D526-S003 Omron, XS2R-D526-S003 Datasheet - Page 9

• Manufacturer Part Number: XS2R-D526-S003
• Description: F3W-D Y PLUG
• Manufacturer: Omron

Specifications of XS2R-D526-S003

• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

F3W-D
● Wiring Precautions
Connection
Cables
Make sure that the bending radius is 25 mm or more.
● Installation Precautions
Installation
Vertical Installation
• The distance between two adjacent sets of Sensors must be at
• Install a baffle so that there will not be mutual interference between
• Before turning ON the power, make sure that the supply voltage is
• Always connect the sync lines.
• Be very careful not to get metal chips in the connector, especially
• Incorrect wiring may damage the equipment. Make sure that the
• Always leave the operation cover closed during operation.
• Applying excessive force to the mode switch may result in damage.
• Install the Sensor so that its sensing face will not receive light from
• Do not strike the Sensor with a hammer or any other tool during
least l
Sensors with the same frequency setting. l
the distance shown in Parallel Operating Range of the Engineering
Data.
Sensors with the same frequency setting. (See Figure 1.)
A light reflection from the wall or floor may go around a baffle and
reach the Receivers. Install a baffle so that it will also block any light
reflection. (See Figure 2.)
within the maximum allowable voltage range.
during wiring.
cable length and routing are appropriate to prevent the connectors
and cables from getting disconnected.
Do not apply a force of more than 5 N.
the sun, fluorescent lamps, incandescent lamps, and other light
sources.
installation, otherwise the internal circuits of the Sensor may be
damaged.
l
1
Emitter
Emitter
Emitter
Emitter
1
or l
Figure 1
Distance X
2
, which does not cause mutual interference between two
Receiver
Receiver
Receiver
Receiver
http://www.ia.omron.com/
Baffle
Emitter
Emitter
Horizontal Installation
l
2
Emitter
Emitter
1
Receiver
Receiver
or l
Figure 2
2
Distance X
Baffle
Baffle
Wall
is at least 1.5 times
Wall
Emitter
Emitter
Receiver
Receiver
Receiver
Receiver
9
Reflection from Wall or Floor
If the Emitter and Receiver are installed as shown in the following
illustration, all the axes may not be interrupted due to light reflection
from the floor or wall. Make sure that the Emitter and Receiver detect
the sensing object properly before using the F3W-D in actual
operation.
Side View
● Adjustment
Operation and Stability Status Display
Error Display
F3W-D052 Picking Sensors are provided with only
one error display mode.
If an error occurs, the indicator on the Sensor’s
Receiver, as indicated by the arrow in the diagram
on the right, will flash.
The error indicated in this example is a
synchronization error.
The possible causes are as follows:
1. The sync line is not connected.
2. The sync line is shorted with another line.
3. UNI-WIRE communications are not being
• Install the Emitter and Receiver in the same orientation as shown in
• Use M4 screws to secure the Sensor body.
• Secure the case to a tightening torque of 1.2 N·m or less.
• The following illustration shows the indicator status corresponding
• Install the Receiver so that the green stability indicators are both
Emitter
the following figure. (The cables must be in the same direction.)
to each incident level.
ON in light receiving status.
performed (when an F3W-D052U UNI-WIRE
Direct Connection Model is being used).
Light-shielded area
* If the Receiver is set to the stable light-receiving area, it will become more
Floor
resistant to environmental fluctuations such as temperature, voltage, dust, and
setting deviation after installation. For applications where a stable light-receiving
area is not obtained, attention must be paid to environmental fluctuations.
Unstable light-
receiving area
receiving area
(c)Copyright OMRON Corporation 2008 All Rights Reserved.
Sensing object
Stable light-
Emitter
*
light received
Amount of
Operating level
× 1.2
Operating level
Receiver
Receiver
Stability indicator
Top View
Emitter
(green)
OFF
ON
Light-ON
Operation indicator (orange)
Emitter
OFF
ON
Wall
Dark-ON
Receiver
OFF
ON
Receiver
9