NT2S-CN002 Omron, NT2S-CN002 Datasheet - Page 26
NT2S-CN002
Manufacturer Part Number
NT2S-CN002
Description
Programming Cable NT2S/NT3S
Manufacturer
Omron
Datasheet
1.NT3S-ST126B-E.pdf
(214 pages)
Specifications of NT2S-CN002
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
- Current page: 26 of 214
- Download datasheet (4Mb)
Hardware
2.1
Please observe the following precautions when installing the unit. Failure to comply with these restric-
tions could result in loss of life, serious personal injury, or equipment damage.
2.2
The NTXS should be mounted on a panel. Gasket, mounting clamps are provided with each NTXS unit
for proper mounting.
Environmental Considerations:
Make sure that the unit is installed correctly and that the operating limits are followed (see Specifications
for NTXS).
Do not operate NTXS in areas subject to explosion hazards due to flammable gases, vapors or dusts.
NTXS should not be installed where fast temperature variations are present. Highly humid areas are
also to be avoided. High humidity causes condensation of water in the unit.
Location Considerations:
Care should be taken when locating equipment behind the NTXS to ensure that AC power wiring, PLC
output modules, contactors, starters, relays and any other source of electrical interference are located
away from NTXS. Particular care should be taken to the position of Variable speed drives and switching
power supplies away from the NTXS.
Panel Mounting
This section presents the dimensional sketches and panel cutouts for NTXS models.
(All dimensions are in mm. Not to Scale.)
20
!
!
!
!
Safety Precaution
Installation Instructions
Warning: Do not operate the HMI in areas subject to explosion due to flammable
Warning: Do not connect the HMI to an AC power source. You will cause permanent
Warning: Do not attempt to use a DC power supply that does not meet HMI power
Warning: Do not power the HMI with a DC power supply used for inductive loads or for
input circuitry to the programmable logic controller. Severe voltage spikes
caused by these devices may damage the HMI.
gases, vapors, or dusts.
damage to the HMI.
requirements. You may cause malfunction or permanent damage to HMI.
Related parts for NT2S-CN002
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
LCD Display Panel
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
LCD Display Panel
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
LCD Touch Panels 2x16LCD8FKEY+NMPAD MSSGDISP 5V
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
LCD Touch Panels 2x16 LCD MESSAGE DISPLAY 5VDC
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
LCD Touch Panels 2x16 LCD 6FKEY 5VDC
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
LCD Touch Panels 2x16LCD 8FKEY+NUMPAD 5VDC
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
LCD Touch Panels 2x16 LCD 6FKEY RTC 24VDC
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
LCD Touch Panels 2x16LCD 8FKEY+NUMPAD RTC 24V
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
LCD Touch Panels 5M Toolbus Port Cbl l for NT2S
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
PLC Interface Cable
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
LCD Touch Panels SF121 TO TOOLBUS PORT CBL 2M
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
LCD Touch Panels SF122 TO TOOLBUS PORT CBL 2M
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
LCD Touch Panels 9-Pin to PRPH PRT Cable 5M V2
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
LCD Touch Panels 9 PIN TO PERIPH PORT CABLE 2M
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
LCD Touch Panels 2M toolbus port cable for NT2
Manufacturer:
Omron
Datasheet: