DRT2-OD08 Omron, DRT2-OD08 Datasheet - Page 456
![no-image](/images/manufacturer_photos/0/4/494/omron_sml.jpg)
DRT2-OD08
Manufacturer Part Number
DRT2-OD08
Description
DRT2 8 Out TermOutal NPN
Manufacturer
Omron
Datasheet
1.DRT2-OD16.pdf
(600 pages)
Specifications of DRT2-OD08
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
- Current page: 456 of 600
- Download datasheet (13Mb)
Temperature Input Terminals
Note
Note In order to perform the adjustment procedure properly, always allow sufficient
■
Resetting User Adjustments
If it is necessary to reset the upper limit adjustment value, lower limit adjust-
ment value, and bias compensation value to the factory defaults, click the
Default Setting Button. The settings will be returned to the factory settings.
The upper/lower limit adjustment values and bias compensation value are all
initialized at the same time.
1. The bias compensation value may not be accepted if there is a large tem-
2. Always test the indication accuracy after making user adjustments to verify
time for temperature stabilization, as shown in the following diagram. Also
allow sufficient time for devices such as the STV, DMM, and ZERO-CON to
stabilize. Refer to each device’s operating manual for details.
STV
perature difference between the Terminal Block and ZERO-CON (0 ° C
bath). If this problem occurs, correct the adjustment system by using a ZE-
RO-CON compatible with the sensor being adjusted or other means.
that the adjustments are correct. Test the indication accuracy at three
points: the lower limit value, an intermediate value, and the upper limit val-
ue.
Note Always use the compensating conductors (the same kind that will be
• Connect the external devices as shown in the following diagram.
• After verifying that the ZERO-CON is set to 0 ° C, set the STV’s output
voltage to produce a voltage equivalent to the test voltage.
used with the sensor being adjusted) to connect the ZERO-CON to
the DRT2-TS04T’s input terminals.
OUTPUT
ZERO-CON
(0 ° C bath)
INPUT
Compensating
conductors
DRT2-TS04T
Input (–)
Input (+)
Section 7-6
435
Related parts for DRT2-OD08
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![DRT2-MD16S-1](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
DRT2 Mix IO E-Con 8in/out PNP
Manufacturer:
Omron
Datasheet:
![DRT2-OD16MLX](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
DRT2 16 OutMIL Conn Cable With
Manufacturer:
Omron
Datasheet:
![DRT2-ID16ML](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
DRT2 16 In MIL Connector NPN
Manufacturer:
Omron
Datasheet:
![DRT2-ID16ML-1](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
DRT2 16 In MIL Connector PNP
Manufacturer:
Omron
Datasheet:
![DRT2-ID16MLX](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
DRT2 16 In MIL Conn Cable With
Manufacturer:
Omron
Datasheet:
![DRT2-ID16MLX-1](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
DRT2 16 In MIL Conn Cable With
Manufacturer:
Omron
Datasheet:
![DRT2-MD16S](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
DRT2 Mix IO E-Con8 In/out, NPN
Manufacturer:
Omron
Datasheet:
![DRT2-OD08-1](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
DRT2 8 Out TermOutal PNP
Manufacturer:
Omron
Datasheet:
![G6S-2G](/images/no-image3.png)
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
![G3NE-220T](/images/no-image3.png)
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
![G6K-2G-Y](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: