A3AT-90K1-00B Omron, A3AT-90K1-00B Datasheet - Page 30
![no-image](/images/manufacturer_photos/0/4/494/omron_sml.jpg)
A3AT-90K1-00B
Manufacturer Part Number
A3AT-90K1-00B
Description
ASSY.L.P.B.INCLD.FLANGE/SPRING
Manufacturer
Omron
Series
A3Ar
Type
Standardr
Specifications of A3AT-90K1-00B
Circuit
SPST-NO
Switch Function
Off-Mom
Contact Rating @ Voltage
6A @ 125VAC
Actuator Type
Round Button
Mounting Type
Panel Mount
Termination Style
Solder Lug
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Illumination Type, Color
-
Illumination Voltage (nominal)
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
A3AT90K100B
- Current page: 30 of 265
- Download datasheet (11Mb)
A3D
Precautions
Refer to the Common Precautions for Pushbutton Switches on
page 14.
Correct Use
Mounting
Always make sure that the power is turned OFF before mounting,
removing, or wiring the Switch, or performing maintenance.
Do not tighten the mounting ring excessively using pliers or a similar
tool. Excessive tightening may damage the mounting ring. (Tighten-
ing torque: 0.20 to 0.29 N⋅m)
Wiring
When wiring, use wires of a size appropriate for the applied voltage
and carry current. Perform soldering correctly under the conditions
given below. Using the Switch with the wires soldered incorrectly
may cause the terminals to become abnormally hot and cause a fire.
Wait for one minute after soldering before exerting any external
force on the solder.
Use a non-corrosive rosin liquid for the flux.
Perform wiring so that the wire sheaths do not come into contact
with the Switch. If this is unavoidable, use wires that can withstand
temperatures of 100°C min.
After wiring to the Switch has been completed, ensure an appropri-
ate insulation distance.
LED
The polarity of the LED is indicated on the back of the Switch. Wire
the LED correctly according to the polarity.
The built-in LED does not have a limiting resistor. Connect a limiting
resistor.
Make sure that the limiting resistor satisfies the characteristics of
the built-in LED. The forward current of the built-in LED must be
8 mA minimum.
The resistance can be calculated by using the following expression.
Recommended Values for Limiting Resistance
Note: The above values are calculated values that can be used as
28
Cat. No. A031-E1-05
5 VDC
12 VDC
24 VDC
1. Hand soldering: At 30 W within 5 seconds.
2. Dip soldering: At 240°C within 3 seconds.
R = (E –V
E:
V
I
Voltage
F
F
:
: LED forward voltage (V)
reference.
Operating voltage (V)
LED forward current (A)
F
)/I
F
165 Ω
515 Ω
1,100 Ω
(Ω)
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
Red
140 Ω
490 Ω
1,090 Ω
(White)
Yellow
145 Ω
495 Ω
1,095 Ω
Green
Calculation Example for Limiting Resistance
Conditions: Red LED with an I
From the red LED characteristic given previously, V
when I
Thus the recommended resistance is 1.1 kΩ at 1 W (2 x I
note)
Note: A factor of 2 is applied because the permissible wattage of
Operating Environment
Ensure that dust, metal powder, or oil do not enter the interior of the
Switch.
Using Microloads
Using a standard load switch for opening and closing a microload
circuit may cause wear on the contacts. Use the switch within the
operating range. (Refer to the diagram below.) Even when using mi-
croload models within the operating range shown below, if inrush
current occurs when the contact is opened or closed, it may cause
the contact surface to become rough, and so decrease life expec-
tancy. Therefore, insert a contact protection circuit where neces-
sary. The minimum applicable load is the N-level reference value.
This value indicates the malfunction reference level for the reliability
level of 60% (λ 60) (conforming to JIS C5003). The equation, λ 60 =
0.5 x 10
than 1/2,000,000 with a reliability level of 60%.
F
–4
the resistor must be twice as large as the required wattage.
is 20 mA. Therefore, R = (24 V – 1.7 V)/0.02 A = 1,100 Ω.
/times indicates that the estimated malfunction rate is less
Invalid
area
Microload
area
F
of 20 mA at 24 V and a Ta of 25°C.
Current (mA)
Standard
load area
F
will be 1.7 V
F
2
R). (see
A3D
Related parts for A3AT-90K1-00B
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![A3AT-90B1-00EG](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
Pushbutton Switch
Manufacturer:
Omron
Datasheet:
![A3AT-90A1-00A](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
PUSHBUTTON SWITCH
Manufacturer:
Omron
Datasheet:
![A3AT-90A1-00L](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
Push Button Switch
Manufacturer:
Omron
Datasheet:
![A3AT-90A1-00R](/photos/41/29/412951/a3at-90k1-00y_tmb.jpg)
Part Number:
Description:
PUSHBUTTON SWITCH
Manufacturer:
Omron
Datasheet:
![A3AT-90B1-00G](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
PUSHBUTTON SWITCH
Manufacturer:
Omron
Datasheet:
![A3AT-90K1-00A](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
ASSY.L.P.B.INCLD.FLANGE/SPRING
Manufacturer:
Omron
Datasheet:
![A3AT-90K1-00D](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
ASSY.L.P.B.INCLD.FLANGE/SPRING
Manufacturer:
Omron
Datasheet:
![A3AT-90K1-00EG](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
ASSY.L.P.B.INCLD.FLANGE/SPRING
Manufacturer:
Omron
Datasheet:
![A3AT-90K1-00ER](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
ASSY.L.P.B.INCLD.FLANGE/SPRING
Manufacturer:
Omron
Datasheet:
![A3AT-90K1-00EY](/images/manufacturer_photos/0/4/494/omron_tmb.jpg)
Part Number:
Description:
ASSY.L.P.B.INCLD.FLANGE/SPRING
Manufacturer:
Omron
Datasheet:
![G6S-2G](/images/no-image3.png)
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
![G3NE-220T](/images/no-image3.png)
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
![G6K-2G-Y](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: