A22Z-B101Y Omron, A22Z-B101Y Datasheet - Page 43

• Manufacturer Part Number: A22Z-B101Y
• Description: PB ENCL. 1 HOLE YELLOW
• Manufacturer: Omron
• Type: Control Boxr
• Series: A22r

Specifications of A22Z-B101Y

• Accessory Type: Control Box Enclosure
• Color: Yellow
• Illumination: Not Illuminated
• Height: 69.5 mm
• Length: 75 mm
• Mounting Style: Panel
• Termination Style: Wire
• Width: 68 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: A22 Series
• For Use With: A22EL-M - SWITCH UNIT PB EMRGNCY STOP 40MMA22E-SK - SWITCH UNIT PB EMERGNCY STOP KEYA22E-S - SWITCH UNIT PB EMRGNCY STOP 30MMA22E-MP - SWITCH UNIT PB EMRGNCY STOP 40MMA22E-MK - SWITCH UNIT PB EMERGNCY STOP KEYA22E-M - SWITCH UNIT PB EMRGNCY STOP 40MMA22E-L - SWITCH UNIT PB EMRGNCY STOP 60MMA22EL-M-T2-11 - SWTCH PB EMRGNCY STOP ILLUM SPSTA22EL-M-T2-02 - SWTCH PB EMRGNCY STOP ILLUM DPSTA22EL-M-T2-01 - SWTCH PB EMRGNCY STOP ILLUM SPSTA22EL-M-T1-11 - SWTCH PB EMRGNCY STOP ILLUM SPSTA22EL-M-T1-02 - SWTCH PB EMRGNCY STOP ILLUM DPSTA22EL-M-24A-11 - SWTCH PB EMRGNCY STOP ILLUM SPSTA22EL-M-24A-02 - SWTCH PB EMRGNCY STOP ILLUM DPSTA22EL-M-12A-11 - SWTCH PB EMRGNCY STOP ILLUM SPSTA22EL-M-12A-02 - SWTCH PB EMRGNCY STOP ILLUM DPSTA22EL-M-12A-01 - SWTCH PB EMRGNCY STOP ILLUM SPSTA22E-SK-11 - SWITCH PB EMRGNCY STOP SPST-NO/CA22E-SK-02 - SWITCH PB EMERGENCY STOP DPST-NCZ3128 - SWITCH PB EMRGNCY STOP SPST-NO/CA22E-S-02 - SWITCH PB EMERGENCY STOP DPST-NCA22E-S-01S - SWITCH PB EMERGENCY STOP SPST-NCA22E-MP-02 - SWITCH PB EMERGENCY STOP DPST-NCA22E-MK-02 - SWITCH PB EMERGENCY STOP DPST-NCZ3129 - SWITCH PB EMRGNCY STOP SPST-NO/CA22E-M-02 - SWITCH PB EMERGENCY STOP DPST-NCA22E-LP-11 - SWITCH PB EMRGNCY STOP SPST-NO/CA22E-LP-02 - SWITCH PB EMERGENCY STOP DPST-NCA22E-L-11 - SWITCH PB EMRGNCY STOP SPST-NO/CA22E-L-02 - SWITCH PB EMERGENCY STOP DPST-NCZ1511 - SWTCH PB EMRGNCY SPST-NC ILLZ1510 - SWTCH PB EMRGNCY SPST-NC ILLZ1509 - SWITCH PB EMRGNCY STP SPST-NCZ1508 - SWITCH PB EMRGNCY STP SPST-NCZ1507 - SWITCH PB EMRGNCY SPST-NO/NCZ1506 - SWITCH PB EMRGNCY STP SPST-NCZ1560 - SWITCH PB EMRGNCY SPST-NO/NCZ1505 - SWITCH PB EMRGNCY STP SPST-NCZ1504 - SWITCH PB EMRGNCY STP SPST-NCZ1503 - SWITCH PB EMRGNCY STP SPST-NCZ1502 - SWITCH PB EMRGNCY STP SPST-NC
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: A22Z-B101Y; A22ZB101Y; Z1648

Removing the Switch Unit
Insert a screwdriver between the Mounting Latch and the Switch
Unit, then push down the screwdriver in the direction indicated by
the arrow in the following figure.
J WIRING
Wiring Round Crimp Terminals
Loosen the terminal screw from the Switch Unit until it completely
comes off the groove, insert a screwdriver as shown in the following
figure, then push up the washer in the direction indicated by the
arrow to temporarily secure it. Now, a round crimp terminal can be
connected. After inserting the terminal, tighten the screws to com-
plete wiring.
Common To All Assemblies
Washer
Screw
Use either of the following screwdrivers.
Flat-head
screwdriver
Phillips
screwdriver
Screwdriver
Screwdriver
44
J ENGRAVING
Engrave the characters on the surface on the Cap. Make sure
that the characters are aligned parallel to the imaginary line
connecting the two protruding portions to the left and right of the
Cap.
The characters must not be engraved deeper than 0.5 mm. Apply
an alcohol-based paint coating, such as melamine, alkyd, or
acrylic resin paint coating, to the engraved characters.
J AFFIXING CHARACTER FILM
Hold the Cap, remove the cardboard on the Film, and attach the Film
to the Cap. Make sure that the protruding portions of the Cap en-
gage the cutout portions of the Film and that the characters are
aligned parallel to the imaginary line connecting the two protruding
portions to the left and right of the Cap.
J MOUNTING AND DISMOUNTING
Press and secure the Snap-in Legend Plate onto the Legend
Plate Frame.
The direction of the characters will vary with the mounting
direction of the control panel if the Switch is a knob or key
selector model.
Protruding portions on Cap
Concave surface
SNAP-IN LEGEND
Protruding portions on Cap
Common To All Assemblies
Legend Plate Frame
Remove the cardboard.
Snap-in Legend Plate