SNDJ-D3C-G01 Honeywell Sensing and Control, SNDJ-D3C-G01 Datasheet - Page 2

• Manufacturer Part Number: SNDJ-D3C-G01
• Description: DIFFERENTIAL HALL SENSOR
• Manufacturer: Honeywell Sensing and Control
• Series: SNDJr
• Type: Hall Effectr

Specifications of SNDJ-D3C-G01

• Output Type: Digital
• Actuator Material: Ferrous Metals, Gear Tooth
• Termination Style: Connector
• Frequency: 25kHz
• Voltage - Supply: 8 V ~ 32 V
• Must Operate: *
• Must Release: *
• Function: *
• Package / Case: Barrel, Stainless Steel, Flange Mount
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 480-2821

SNDJ-D3*-G01 Series
SENSOR SPECIFICATIONS
Characteristic
Supply voltage
Current consumption
Signal outputs
Frequency range
Insulation
Operating temperature
Housing
Cable/connector
Protection class
Vibration immunity
Shock immunity
Weight
Air gap
Pole wheel
NOTICE
INSTALLATION INFORMATION
•
•
•
2
The sensor wires must be laid as far as possible from
large electrical machines. They must not run parallel with
power cables. The maximum permissible cable length is
20 m [65 ft].
The sensor should be mounted with the middle of the face
side over the middle of the pole wheel. Where the pole
wheel has teeth or slots with radial sensor location, the
sensor would normally be mounted over the center.
Dependent upon the wheel width, a degree of axial
movement is permissible.
A solid and vibration-free mounting of the sensor is
important.
www.honeywell.com/sensing
Parameter
8 Vdc to 32 Vdc, protected against reverse polarity
14 mA max. (without load)
Square wave signal from push-pull stage, dc-coupled to the supply (negative pole = reference
voltage)
30 mA max. load
Output voltage HI: > power supply voltage 3.6 V (at I = 25 mA), 2.5 V (at I = 10 mA)
Output voltage LO: < 2.2 V (at I = 25 mA), 1.4 V (at I = 10 mA)
The output is short-circuit proof and protected against false polarity
5 Hz to 25 kHz
Housing, cable shield, and electronic galvanically isolated (500 V/50 Hz/1 min.)
-20 °C to 100 °C [-4 °F to 212 °F]
Stainless steel 1.4305
P variant: with cable PUR, three wires 0.34 mm
C variant: with connector 4-pins/M12 standard
Sensor head IP68, cable/entrance IP67, connector IP68 (mated)
30 g in the range 5 Hz to 2000 Hz
50 g during 20 ms, half-sine wave
D3C-G01: ~40 g
D30-G01: ~60 g, including 0,35 m cable
For pole wheel M 0.5 (DP 50.8): 0,1 mm to 0,3 mm [0.004 in to 0.012 in]
For pole wheel M1 (DP 25.4): 0,1 mm to 1,5 mm [0.004 in to 0.06 in]
For pole wheel M2 (DP 12.7): 1,0 mm to 2,0 mm [0.04 in to 0.08 in]
Ferromagnetic toothed wheel, i.e. B. USt37-2, preferred involute gear form Module >1, min.
tooth width 6 mm [0.24 in], side offset with min. tooth width: <0,2 mm [0.008 in],
eccentricity <0,2 mm [0.008 in]
2
(AWG 22)