LAT-1-SFP30 BANNER ENGINEERING, LAT-1-SFP30 Datasheet - Page 2

• Manufacturer Part Number: LAT-1-SFP30
• Description: LAT-1-SFP30 LASER ALGNMNT
• Manufacturer: BANNER ENGINEERING

To align a safety light screen using the LAT-1:
1. Mount all sensors and corner mirrors per the instructions in
2. Assemble the appropriate clip to the LAT-1; snap it onto the
3. If the sensors are mounted vertically, check the circular
4. Standing behind the Alignment Tool, view the retroreflective
5. Move the Alignment Tool and the retroreflective target to the
6. Repeat steps 4 and 5 until the image falls at the desired
P/N 54599 rev. D
Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN USA 55441 • Phone: [phone] • www.bannerengineering.com • Email: [e-mail]
Supply Voltage and Current
Sensing Beam
Beam Size at Aperture
Beam Divergence
Beam Placement
Construction
Environmental Rating
Operating Conditions
Laser Classification
Application Notes
the appropriate manual. Leave the hardware slightly loose to
allow for positioning adjustment.
light screen emitter or receiver, and slide it to one end of
the sensor. (HINT: Check the receiver for plumb first, before
attaching the LAT-1 to the emitter for alignment.) Attach a
retroreflective target to the corresponding end of the opposite
sensor.
bubble level for plumb orientation.
target from behind the sensor (see Figure 2). Adjust either or
both sensors and/or the corner mirrors as needed to place the
laser image at the desired spot on the opposite sensor.
opposite ends of the sensors and repeat step 4.
spot at both the top and bottom of the opposite sensor; then
tighten all mounting hardware.
Alignment Procedure
One standard 9V battery, included (replaceable); approximately 20 hours of continuous operation
Class 2 laser, 640-660 nm visible red IEC
Pulse Width: 7 µs
Rep rate: 30 µs
Peak output power: 2.8 mW, 33kHz, 25% duty cycle
Approximately 2 mm (0.08”) diameter
± 1.0 milliradian within specified temperature range
± 0.5 milliradians at room temperature
Within ± 4 milliradians (approximately ±0.25 degrees) of parallel to front, back, top and bottom of
housing
Aluminum housing; black anodized finish
Black polypropylene cover with flexible hinge for battery access
NEMA 1; IEC IP50
Temperature: 0° to +40°C (+32° to 104°F)
Maximum Relative Humidity: 90% @ +50°C (non-condensing)
U.S. Safety Standards 21 CFR 1040.10
European Standards EN 60825-1:1994
See Caution on page 1 regarding safe use of laser beam.
®
Specifications
Figure 2. Aligning a corner-mirror light screen application using the
WARRANTY: Banner Engineering Corp. warrants its products
to be free from defects for one year. Banner Engineering
Corp. will repair or replace, free of charge, any product of its
manufacture found to be defective at the time it is returned to
the factory during the warranty period. This warranty does not
cover damage or liability for the improper application of Banner
products. This warranty is in lieu of any other warranty either
expressed or implied.
Laser Alignment Tool
Receiver
Retroreflective
Target
Emitter
Mirror 2
DO
LASER
REMOVE
LASER
DO
REMOVE
NOT
STARE
LIGHT
Peak
TWO
REQUIR
PHILLIPS
NOT
STARE
LIGHT
Peak
TWO
PHILLIPS
REQUIR
INTO
BEAM.
Power:
2.8
33kHz
COMPLIES
WITH
1040.10
AVOID
EXPOSURE
EMITTED
AND
SCREWS
FROM
INTO
BEAM.
Power:
AVOID
2.8
33kHz
COMPLIES
WITH
1040.10
AND
EXPOSURE
EMITTED
FROM
SCREWS
CLASS
2 LASER
mW,
660-680nm
25%
duty
21
CFR
EN60825-1
- LASER
THIS
APERTURE
ES
ONE
FOR
BATTERY
CLASS
2 LASER
mW,
660-680nm
25%
duty
21
EN60825-1
- LASER
CFR
FOR
THIS
APERTURE
ES
ONE
BATTERY
PRODUCT.
LAT
- 1
cycle
PART
; 1994
LIGHT
ACCESS
9V
BATTER
LAT
PRODUCT.
- 1
cycle
PART
; 1994
LIGHT
9V
ACCESS
BATTER
Y
BELOW
BELOW
Y
LAT-1
Laser Alignment
Tool
Mirror 1