ST1-L2-DC5V-F PANASONIC EW, ST1-L2-DC5V-F Datasheet - Page 3

• Manufacturer Part Number: ST1-L2-DC5V-F
• Description: ST Relay (2 Coil Latch, AgSnO2)
• Manufacturer: PANASONIC EW

ST
2. Specifications
Notes: *1 This value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the
REFERENCE DATA
1. Max. switching power
Contact
Rating
Electrical
characteristics
Mechanical
characteristics
Expected life
Conditions
Unit weight
Characteristics
*2 Wave is standard shock voltage of 1.2 50 s according to JEC-212-1981
*3 Refer to 6. Conditions for operation, transport and storage mentioned in AMBIENT ENVIRONMENT
0.5
0.2
0.1
10
5
2
1
actual load.
DC resistive load
10
20
Arrangement
Contact material
Initial contact resistance, max.
Max. switching power (resistive load)
Max. switching voltage
Max. switching current
Minimum operating power
Nominal operating power
Min. switching capacity (Reference value)*
Insulation resistance (Initial)
(at 25 C, 50% relative humidity)
Breakdown voltage
(Initial)
Surge breakdown voltage (Initial)*
Operate time [Set time] (at 20 C
Release time [Reset time] (at 20 C
Temperature rise (at 60 C
Shock resistance
Vibration resistance
Mechanical
Electrical
Conditions for operation, transport and storage*
Max. operating speed
AC
inductive load
(cos
50
Voltage, V
100 200 300
AC resistive load
)
Between open contacts
Between contact sets
Between contact and coil
Functional
Destructive
Functional
Destructive
Item
140
All Rights Reserved © COPYRIGHT Matsushita Electric Works, Ltd.
F)
68
2
68
2. Coil temperature rise
F)
F)
1
100
90
80
70
60
50
40
30
20
10
0
3
Contact current 8A
0.2
1 Form A 1 Form B, 2 Form A
Au-flashed AgSnO
Max. 30 m (By voltage drop 6 V DC 1A)
3,040 VA, 150 W
380 V AC, 250 V DC
8 A
150mW (Single side stable, 2 coil latching)
240mW (Single side stable, 2 coil latching)
100 mA 5V DC
Min. 1,000M
Measurement at same location as “Initial breakdown voltage” section.
1,200 Vrms for 1 min. (Detection current: 10 mA)
2,000 Vrms for 1 min. (Detection current: 10 mA)
3,750 Vrms for 1 min. (Detection current: 10 mA)
6,000 V (Between contact and coil)
Max. 15 ms [Max. 15 ms]
(Nominal voltage applied to the coil, excluding contact bounce time.)
Max. 10 ms [Max. 15 ms]
(Nominal voltage applied to the coil, excluding contact bounce time.) (without diode)
Max. 55 C
(By resistive method, nominal voltage applied to the coil; contact carrying current: 8A.)
Min. 196 m/s
Min. 980 m/s
10 to 55 Hz at double amplitude of 2 mm (Detection time: 10 s.)
10 to 55 Hz at double amplitude of 3 mm
Min. 10
Min. 10
Ambient temperature: –40 C to +60 C
Humidity: 5 to 85% R.H. (Not freezing and condensing at low temperature)
30 cps
Approx. 10g
0.4
Coil operating power, W
7
5
(at 180 cpm)
(8 A 250 V AC resistive) (ON : OFF = 1 s : 5 s)
0.6
.353 oz
2
2
(Half-wave pulse of sine wave: 11 ms; detection time: 10 s.)
(Half-wave pulse of sine wave: 6 ms.)
(at 500V DC)
0.8
0A
2
type
1.0
1.2
Specifications
–40 F to +140
3. Influence of adjacent mounting
-10
-20
-30
-40
40
30
20
10
0
F;
5
Inter-relay distance, mm
Drop-out voltage
Pick-up voltage
10
15
20