XS2F-D421-410 Omron, XS2F-D421-410 Datasheet - Page 24
![no-image](/images/manufacturer_photos/0/4/494/omron_sml.jpg)
XS2F-D421-410
Manufacturer Part Number
XS2F-D421-410
Description
CONNECTOR
Manufacturer
Omron
Datasheet
1.XS2F-D421-410.pdf
(27 pages)
Assembly Procedure for XS2C/XS2G Connector Assemblies
(1) Connector and Cable External Diameters
Note: When connecting a commercially available cable to a connector
(2) Component Insertion
• Connectors for 6-, 4-, and 3-mm-diameter Cables (i.e.,
• Connectors for 6-mm-diameter Cables use white cable
Crimping/Soldering Connectors
Straight Connectors
L-shaped Connectors
• As shown in the above illustration, connect the above
Screw-on Connectors
Confirm that you have all of the required parts.
Cables that are 5 to 6, 4 to 5, and 3 to 4 mm in diameter
respectively) are available. When assembling a Connector
used with a cable, make sure that the external diameter of
the Connector is suited to that of the cable.
clamps. Connectors for 4- and 3-mm-diameter Cables use
black cable clamps.
A watertight bushing for 6-mm-diameter Cable has no
stripe, that for 4-mm-diameter Cable has a single stripe, and
that for 3-mm-diameter Cable has two stripes.
components to the Cable with its end processed.
Insulation caps and insulation tubes are included with
5-pole Connectors (XS2C-D5S@ and XS2G-D5S@).
*1.Rings are not required with 7-mm and 8-mm cables.
*2.Insert the waterproof bushing for 7-mm and 8-mm
assembly, use a cable with an outside diameter of 3 to 6 mm and core
sizes of 0.18 to 0.75 mm
for soldering connectors.
cables in the direction shown in the diagram.
*A ring is not required for Screw-on Connectors.
Cover
Cover
Cover
Cover
2
for crimping connectors and 0.5 mm
Ring *1
Ring (L-shaped models only) *
Watertight
bushing
Watertight
bushing
Watertight
bushing
Watertight bushing
Cable clamp
Cable clamp
Cable
clamp
Cable clamp
Cap
Cap
Cap
Cap
*2
2
maximum
(3) Wiring (Processing Cable Ends)
Crimping
Wiring
• Strip 10 mm of the Cable sheath and 4 mm of each core.
• Before soldering cores and solder cup pins together, solder-
• The following conditions are recommended for soldering
• The length marked *A should be 6.5 mm max., otherwise
• Strip 14 mm of the Cable sheath and 4 mm of each core.
• Make sure that each core is not damaged and its end
• Mount the XY2F-0003 Locator to DMC's AFM8 (M25520/2-
• After mounting the crimping pins to the Locator, fully insert
• Squeeze the handle of the Crimp Tool to press-fit the cores
• After press-fitting the cores to the pins, insert the pins into
Soldering Connectors
Crimping Connectors
coat each of them.
each solder cup pin.
Soldering iron: 30 to 60 W
Soldering temperature: 280°C to 340°C
Soldering period: 3 s max.
the proper degree of protection of the connector will not be
maintained.
strands are not spread out.
01) Crimping Tool, both of which are sold separately, and
set the selector dial of the Crimping Tool to 6 for the XS2U-
@@21 and to 7 for the XS2U-@@22.
the cores to the crimping pins.
to the crimping pins.
(Squeeze the handle firmly until the handle automatically
returns to the release position.)
the pin clamp as shown in the illustration. Then make sure
that the lead colors correspond to the pin clamp numbers
that are identical to the connector pin numbers.
Pin clamp
Press
6
±0.5
1 to 1.5
*A
XS2
24