VX-52-1C23 Omron, VX-52-1C23 Datasheet - Page 6

• Manufacturer Part Number: VX-52-1C23
• Description: MINIATURE BASIC SWITCH
• Manufacturer: Omron
• Series: VXr
• Type: Snap Actionr

Specifications of VX-52-1C23

• Circuit: SPDT
• Switch Function: On-Mom
• Contact Rating @ Voltage: 5A @ 250VAC
• Actuator Type: Lever, Straight
• Mounting Type: Chassis Mount
• Termination Style: Quick Connect - .187" (4.7mm)
• Operating Force: 30gf
• Contact Form: SPDT
• Contact Rating: 5 Amps
• Actuator: Lever
• Body Style: Miniature
• Current, Rating: 5 A
• Dielectric Strength: 1500 VAC
• Mounting Hole Size: 3.1 mm
• Number Of Poles: 1
• Operation: Snap Action
• Termination: Quick Connect
• Voltage, Rating: 125/30 VAC/VDC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: SW995; VX-52-1C23; VX521C23

VX
Precautions
Refer to General Information.
■
Handling
Be careful not to drop the Switch. Doing so may cause damage to
the Switch’s internal components because it is designed for a
small load.
■
Mounting
Use M3 mounting screws with plane washers or spring washers
to securely mount the Switch. Tighten the screws to a torque of
0.39 to 0.59 N·m {4 to 6 kgf·cm}.
Mounting Direction
For a Switch with an actuator, mount the Switch in a direction
where the actuator weight will not be applied to the Switch.
Since the Switch is designed for a small load, its resetting force is
small. Therefore, resetting failure may occur if unnecessary load
is applied to the Switch.
6
Short Hinge Roller Lever Models
Hinge Roller Lever Models
Cautions
Correct Use
OP
PT
PT
OP
3.4±0.15 dia.
2.8
2.8
3.4±0.15 dia.
3.1
t = 0.5 (stainless-steel lever)
3.1
+0.13
10.3±0.1
−0.03
A
+0.13
10.3±0.1
−0.03
t = 0.5 (stainless-steel lever)
A
22.2±0.1
34.0±0.8
27.8
22.2±0.1
37.8±0.8
27.8
20.1
37.8±0.8
8.1
8.1
(10)
1.6
2.8
3.1
(10)
4.8 dia. × 4.8 (oilless polyacetar resin roller)
3.1
1.6
2.8
+0.13
−0.03
Three, solder terminals
+0.13
−0.03
15.9 18.8
Three, solder terminals
dia. holes
15.9 18.8
dia. holes
4.8 dia. × 4.8
(oilless polyacetar resin roller)
Using Micro Loads
Using a model for ordinary loads to open or close the contact of a
micro load circuit may result in faulty contact. Use models that
operate in the following range. However, even when using micro
load models within the operating range shown below, if inrush
current occurs when the contact is opened or closed, it may
increase contact wear and so decrease durability. Therefore,
insert a contact protection circuit where necessary.
The minimum applicable load is the N-level reference value. This
value indicates the malfunction reference level for the reliability
level of 60% (λ 60). The equation, λ 60 = 0.5×10
indicates that the estimated malfunction rate is less than 1/
2,000,000 operations with a reliability level of 60%.
10.3
5.1
10.3
Inoperable
range
5.1
Operating range
for micro load
models VX-01
OF max.
RF min.
PT max.
OT min.
MD max.
OP
Note:
OF max.
RF min.
PT max.
OT min.
MD max.
OP
Model
Model
The values indicated in parentheses
are reference values for cases when
the installation direction is such that
the lever weight is not applied to the
plunger.
0.29 N {30 gf}
---
4.0 mm
1.6 mm
0.8 mm
20.7±1.2 mm
0.59 N {60 gf}
0.04 N {4 gf} (reference value)
1.6 mm
0.8 mm
0.5 mm
20.7±0.6 mm
VX-56-1@3
VX-55-1@3
Current (mA)
Operating
range for
general-
load models
VX-5
VX-016-1@3
VX-015-1@3
–6
/operations
VX