M7E-12DKN2 Omron, M7E-12DKN2 Datasheet
M7E-12DKN2
Specifications of M7E-12DKN2
Related parts for M7E-12DKN2
M7E-12DKN2 Summary of contents
Page 1
... Model Red M7E-12DRN1 Input level Green M7E-12DGN1 Red/green/orange M7E-12DKN1 Ambient temperature Operating: −10 to 55°C (with no icing) Red M7E-12DRN2 Ambient humidity Green M7E-12DGN2 Red/green/orange M7E-12DKN2 ■ Characteristics Red M7E-12HRN1 Green M7E-12HGN1 Insulation Red/green/orange M7E-12HKN1 resistance Red M7E-12HRN2 Dielectric strength Green M7E-12HGN2 ...
Page 2
... Installation ■ Cables Refer to M7E Options for information on using cables (OMRON G79-@C, G79-Y@C, and G79-O@C-@). ■ Input Codes Negative Logic Standard Unit A N Connector pin No. (CN1) Terminal symbol LE D Input signals Either low or high. All inputs are pulled up internally. Therefore high can be open. ...
Page 3
... Note: If the R and G of the multi-color display are set low, the Unit will display in orange. Function Function The value and symbol corresponding to the input code signal are displayed. Refer to the list of input codes for the contents of display. M7E Terminal Arrangement Models with 120/200-mm-high Characters Supply voltage: 24 VDC 3 ...
Page 4
... Note: 1. The CN2 or CN3 Multi-digit Connector must be used for serial transmission and dynamic control with the B7A Link Terminal. Refer to page 5 for details. Use the CN2 and CN3 for connection with the M7E only. 2. Use the following connectors for the connector terminals: ...
Page 5
... By supplying power to a single display, all the displays will be supplied with power. • The B7A's serial output must be connected to the SI terminal of the rightmost TB1. • Use OMRON's M7E-WH@11A Harness Connectors or equivalent to connect all Units. • The DP and BI terminals can be controlled by transmitting the following special data Hexadecimal C data: Turns ON the decimal point of the relevant digit ...
Page 6
... Signal Allocation B7A-M7E Corresponding Pin List The B7A's switch terminals correspond to the M7E's parallel input signals as follows: B7A switch terminal M7E parallel input A0 First digit A A1 (1's digit ...
Page 7
... When the zero suppression function is not used, the RBI (J9) terminals must be open. The TER (J11) terminals can be either short-circuited or open. • When zero suppression is not used, the RBI (J9) terminals of the M7E Digital Display Unit for the leftmost digit must be short-circuited, those of all the other M7E Digital Display Units must be open, the TER (J11) terminals of the M7E Digital Display Unit for the rightmost digit must be open, and those of all the other M7E Digital Display Units must be short-circuited ...
Page 8
... Inputs the data signal as BCD (or binary code). Low when the decimal point lights. The decimal point can light without regard to the LE signal. Low when the display is turned OFF. Low when the display retained. (High is retained until the signal goes low.) --- (No display) --- M7E 8 ...
Page 9
... A 8 848.6±0.4 LED 7° 5 dia. (max.) 176.4± 0.2 116 267.2± 0.2 Number Dimension of Units A 1 177±0.4 2 353.4±0.4 3 529.8±0.4 4 706.2±0.4 5 882.6±0 1,059±0.4 7 1,235.4±0.4 8 1,411.8±0.4 M7E 120 200 9 ...
Page 10
... Wiring • When wiring with terminals or a connector, remove the rear cover of the M7E and connect the M7E to the terminals or connector properly, and be sure not to leave any wire cuttings inside the Display Unit. • Make sure that no wire is more than five meters long when wiring the B7A link terminal ...
Page 11
... Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. WARRANTY OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by OMRON. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS ...