G6AK-274P-ST40-US-DC12 Omron, G6AK-274P-ST40-US-DC12 Datasheet - Page 8
![LOW SIGNAL RELAY](/photos/17/55/175589/g6at_sml.jpg)
G6AK-274P-ST40-US-DC12
Manufacturer Part Number
G6AK-274P-ST40-US-DC12
Description
LOW SIGNAL RELAY
Manufacturer
Omron
Series
G6Ar
Datasheet
1.G6A-274P-ST-US_DC12_BY_OMR.pdf
(10 pages)
Specifications of G6AK-274P-ST40-US-DC12
Relay Type
General Purpose
Circuit
DPDT (2 Form C)
Contact Rating @ Voltage
2A @ 30VDC
Coil Type
Latching, Dual Coil
Coil Current
30mA
Coil Voltage
12VDC
Control On Voltage (max)
8.4 VDC
Mounting Type
Through Hole
Termination Style
PC Pin
Contact Form
2 Form C
Power Consumption
360 mW
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Control Off Voltage (min)
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
G6AK274PST40USDC12
G6AK-274P-ST(40)-US
G6AU-474P-ST-US
G6AK-474P-ST(40)-US
Precautions
Long-term Continuously ON Contacts
Using the Relay in a circuit where the Relay will be ON continuously
for long periods (without switching) can lead to unstable contacts
because the heat generated by the coil itself will affect the insulation,
causing a film to develop on the contact surfaces. Be sure to use a
fail-safe circuit design that provides protection against contact failure
or coil burnout. Otherwise, use a latching relay.
88
Low Signal Relay
- DISCONTINUED
- DISCONTINUED
0.6
20.2 max.
(20)*
0.6
G6A
0.6
*Average value
35.4 max.
(35.2)*
0.3
35.4 max.
(35.2)*
10.1 max.
(9.9)*
7.62
*Average value
0.64
*Average value
0.3
8.4 max.
(8.2)*
3.16
0.3
10.1 max.
(9.9)*
7.62
10.1 max.
(9.9)*
Terminal Arrangement/
Internal Connections
(Bottom View)
16
Relay Handling
When washing the product after soldering the Relay to a PCB, use a
water-based solvent or alcohol-based solvent, and keep the solvent
temperature to less than 40°C. Do not put the Relay in a cold clean-
ing bath immediately after soldering.
1
7.62
+
-
S R
+
-
0.64
Fourteen, 1.0-dia. holes
Sixteen, 1.0-dia. holes
15
2
0.64
4
13
8.4 max.
(8.2)*
3.16
11
6
8.4 max.
(8.2)*
3.16
(1.2)
9
8
5.08 5.08 5.08 2.54
10
5.08 5.08 5.08
Terminal Arrangement/
Internal Connections
(Bottom View)
7
Terminal Arrangement/
Internal Connections
(Bottom View)
10
Tolerance: ±0.1
7
Mounting Holes
(Bottom View)
Tolerance: ±0.1
Mounting Holes
(Bottom View)
(1.2)
Ten, 1-dia. holes
12
5
12
5
Mounting Holes
(Bottom View)
Tolerance: ±0.1
14
2.54
3
S
14
3
+
-
16
1
5.08
7.62
16
1
5.08
+ -
15
2
S R
- +
13
+
-
R
4
5.08 5.08
13
5.08 5.08
4
5.08 5.08
11
6
11
6
9
8
9
8
(1.2)
7.62
(1.2)
(1.2)
(1.2)
7.62
(1.2)
7.62
(1.2)
(1.2)
(1.2)
(1.2)