ATV21HU55M3X SQUARE D, ATV21HU55M3X Datasheet - Page 2

• Manufacturer Part Number: ATV21HU55M3X
• Description: SPEEDDRIVE 200-240VAC 7.5HP ATV21 V1.6
• Manufacturer: SQUARE D

Torque accuracy
Regulation loop
Motor slip compensation
Diagnostic
Output voltage
Insulation
Recommended type of cable for mounting in an en-
closure
Electrical connection
Tightening torque
Supply
Analogue input number
Analogue input type
Sampling duration
Response time
Accuracy
Linearity error
Analogue output number
Analogue output type
Discrete output number
Discrete output type
Minimum switching current
Maximum switching current
Discrete input type
Discrete input logic
Acceleration and deceleration ramps
Braking to standstill
2
+/- 15 %
Adjustable PI regulator
Adjustable
Automatic whatever the load
Not available in voltage/frequency ratio motor control
1 LED red for DC bus energized
<= power supply voltage
Electrical between power and control
With UL Type 1 kit: 3-strand UL 508 cable at 40 °C, copper 75 °C PVC
Without mounting kit: 1-strand IEC cable at 45 °C, copper 70 °C PVC
Without mounting kit: 1-strand IEC cable at 45 °C, copper 90 °C XLPE/EPR
L1/R, L2/S, L3/T terminal 16 mm² / AWG 6
VIA, VIB, FM, FLA, FLB, FLC, RY, RC, F, R, RES terminal 2.5 mm² / AWG 14
L1/R, L2/S, L3/T 2.5 N.m / 22 lb.in
VIA, VIB, FM, FLA, FLB, FLC, RY, RC, F, R, RES 0.6 N.m
Internal supply at 24 V DC, voltage limits 21...27 V <= 200 mA for overload and
short-circuit protection
Internal supply for reference potentiometer (1 to 10 kOhm) at 10.5 V DC, toler-
ance +/- 5 % <= 10 mA for overload and short-circuit protection
2
VIA switch-configurable current 0...20 mA, impedance 242 Ohm, resolution 11
bits
VIA switch-configurable voltage 0...10 V DC, input voltage 24 V max, impedance
30000 Ohm, resolution 11 bits
VIB configurable PTC probe 0...6 probes, impedance 1500 Ohm
VIB configurable voltage 0...10 V DC, input voltage 24 V max, impedance 30000
Ohm, resolution 11 bits
F 2 ms +/- 0.5 ms for discrete input(s)
R 2 ms +/- 0.5 ms for discrete input(s)
RES 2 ms +/- 0.5 ms for discrete input(s)
VIA 2 ms +/- 0.5 ms for analog input(s)
VIB 2 ms +/- 0.5 ms for analog input(s)
FLA, FLC 7 ms +/- 0.5 ms for discrete output(s)
FLB, FLC 7 ms +/- 0.5 ms for discrete output(s)
FM 2 ms +/- 0.5 ms for analog output(s)
RY, RC 7 ms +/- 0.5 ms for discrete output(s)
FM +/- 1 % for a temperature variation 60 °C
VIA +/- 0.6 % for a temperature variation 60 °C
VIB +/- 0.6 % for a temperature variation 60 °C
FM +/- 0.2 % for output
VIA +/- 0.15 % of maximum value for input
VIB +/- 0.15 % of maximum value for input
1
FM switch-configurable current 0...20 mA, impedance 500 Ohm, resolution 10
bits
FM switch-configurable voltage 0...10 V DC, impedance 470 Ohm, resolution 10
bits
2
FLA, FLC configurable relay logic NO, electrical service life 100000 cycles
FLB, FLC configurable relay logic NC, electrical service life 100000 cycles
RY, RC configurable relay logic NO, electrical service life 100000 cycles
Configurable relay logic 3 mA at 24 V DC
FL, R on inductive load, 2 A at 250 V AC, cos phi = 0.4, L/R = 7 ms
FL, R on inductive load, 2 A at 30 V DC, cos phi = 0.4, L/R = 7 ms
FL, R on resistive load, 5 A at 250 V AC, cos phi = 1, L/R = 0 ms
FL, R on resistive load, 5 A at 30 V DC, cos phi = 1, L/R = 0 ms
F programmable 24 V DC, with level 1 PLC, impedance 3500 Ohm
R programmable 24 V DC, with level 1 PLC, impedance 3500 Ohm
RES programmable 24 V DC, with level 1 PLC, impedance 3500 Ohm
F, R, RES negative logic (sink), state 0 >= 16 V, state 1 <= 10 V
F, R, RES positive logic (source), state 0 <= 5 V, state 1 >= 11 V
Automatic based on the load
Linear adjustable separately from 0.01 to 3200 s
By DC injection