LTC4267IGN Linear Technology, LTC4267IGN Datasheet - Page 11
![no-image](/images/manufacturer_photos/0/3/388/linear_technology_sml.jpg)
LTC4267IGN
Manufacturer Part Number
LTC4267IGN
Description
IC,SMPS CONTROLLER,CURRENT-MODE,CMOS,SSOP,16PIN,PLASTIC
Manufacturer
Linear Technology
Datasheet
1.LTC4267IGN.pdf
(32 pages)
Specifications of LTC4267IGN
Lead Free Status / Rohs Status
Not Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LTC4267IGN
Manufacturer:
LT
Quantity:
10 000
Part Number:
LTC4267IGN
Manufacturer:
LT/凌特
Quantity:
20 000
Part Number:
LTC4267IGN#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
LTC4267IGN#TRPBF
Manufacturer:
LT
Quantity:
3 100
Company:
Part Number:
LTC4267IGN-1
Manufacturer:
LT
Quantity:
10 000
Company:
Part Number:
LTC4267IGN-1#PBF
Manufacturer:
LT
Quantity:
1 045
Part Number:
LTC4267IGN-1#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
LTC4267IGN-1#TRPBF
Manufacturer:
LT
Quantity:
1 145
Part Number:
LTC4267IGN-1#TRPBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LTC4267IGN-3#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
APPLICATIO S I FOR ATIO
Series Diodes
The IEEE 802.3af-defi ned operating modes for a PD refer-
ence the input voltage at the RJ45 connector on the PD.
The PD must be able to accept power of either polarity
at each of its inputs, so it is common to install diode
bridges (Figure 2). The LTC4267 takes this into account
by compensating for these diode drops in the threshold
points for each range of operation. A similar adjustment
is made for the UVLO voltages.
Detection
During detection, the PSE will apply a voltage in the
range of –2.8V to –10V on the cable and look for a 25kΩ
signature resistor. This identifi es the device at the end of
the cable as a PD. With the terminal voltage in this range,
the LTC4267 connects an internal 25kΩ resistor between
the V
compensated resistor presents the proper signature to
alert the PSE that a PD is present and desires power to be
applied. The internal low-leakage UVLO switch prevents
the switching regulator circuitry from affecting the detec-
tion signature.
The LTC4267 is designed to compensate for the voltage
and resistance effects of the IEEE required diode bridge.
PORTP
and V
POWERED DEVICE (PD)
PORTN
U
BY IEEE 802.3af
pins. This precision, temperature
AS DEFINED
INTERFACE
U
RJ45
1
2
3
6
4
5
7
8
W
TX
TX
RX
RX
+
–
+
–
SPARE
SPARE
Figure 2. LTC4267 PD Front End Using
Diode Bridges on Main and Spare Inputs
+
–
U
T1
TO PHY
BR2
The signature range extends below the IEEE range to ac-
commodate the voltage drop of the two diodes. The IEEE
specifi cation requires the PSE to use a ΔV/ΔI measurement
technique to keep the DC offset of these diodes from af-
fecting the signature resistance measurement. However,
the diode resistance appears in series with the signature
resistor and must be included in the overall signature
resistance of the PD. The LTC4267 compensates for the
two series diodes in the signature path by offsetting the
resistance so that a PD built using the LTC4267 will meet
the IEEE specifi cation.
In some applications it is necessary to control whether or
not the PD is detected. In this case, the 25kΩ signature
resistor can be enabled and disabled with the use of the
SIGDISA pin (Figure 3). Disabling the signature via the
SIGDISA pin will change the signature resistor to 9kΩ
(typical) which is an invalid signature per the IEEE 802.3af
specifi cation. This invalid signature is present for PD input
voltages from –2.8V to –10V. If the input rises above –10V,
the signature resistor reverts to 25kΩ to minimize power
dissipation in the LTC4267. To disable the signature, tie
SIGDISA to V
driven high with respect to V
all functions of the PD interface are disabled.
PORTP
D3
BR1
. Alternately, the SIGDISA pin can be
4
V
PORTN
LTC4267
PORTN
V
PORTP
4267 F02
. When SIGDISA is high,
8
LTC4267
11
4267fc