MT9T031C12STC Aptina LLC, MT9T031C12STC Datasheet - Page 4

• Manufacturer Part Number: MT9T031C12STC
• Description: IC SENSOR IMAGE COLOR 48CLCC
• Manufacturer: Aptina LLC
• Series: Micron®DigitalClarity®r
• Type: CMOS Imagingr

Specifications of MT9T031C12STC

• Pixel Size: 3.2µm x 3.2µm
• Active Pixel Array: 2048H x 1536V
• Frames Per Second: 12 ~ 93
• Voltage - Supply: 3 V ~ 3.6 V
• Package / Case: 48-CLCC
• Brief Features: Superior Low Light Performance, Programmable Controls, Low Dark Current, High Frame Rate
• Supply Voltage Range: 3V To 3.6V
• Operating Temperature Range: 0°C To +60°C
• Ic Function: Digital Image Sensor
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 557-1450 - KIT HEAD BOARD FOR MT9T031557-1451 - KIT DEV FOR MT9T031
• Lead Free Status / Rohs Status: Compliant
• Other names: 557-1452

Table 3:
PDF: 09005aef824c997f/Source: 09005aef824c998a
MT9T031_3100_PB_2.fm - Rev. A 8/06 EN
15, 17, 18, 21, 47, 48
2, 3, 6, 9, 11,14,19,
24, 25, 26, 27, 28,
32, 33, 34, 35, 36
Pin Numbers
5, 23, 38, 43
.
30 42, 44
4, 22, 37
16, 20
10
13
29
46
12
45
31
39
40
41
7
8
1
Pin Descriptions
FRAME_VALID
LINE_VALID
GSHT_CTL
STANDBY
D
TRIGGER
Symbol
STROBE
EXTCLK
VAAPIX
RESET#
PIXCLK
OUT
S
D
A
SCLK
OE#
V
V
DATA
NC
GND
GND
DD
AA
[9:0]
Output
Output
Output
Output
Output
Supply
Supply
Supply
Supply
Supply
Input
Input
Input
Input
Input
Input
Type
Input
I/O
–
Standby: Activates (HIGH) standby mode, disables analog bias circuitry
for power saving mode.
Trigger: Activates (HIGH) snapshot sequence.
Reset: Activates (LOW) asynchronous reset of sensor. All registers
assume factory defaults.
Output enable: OE# when HIGH, places outputs D
FRAME_VALID, LINE_VALID, PIXCLK, and STROBE into a tri-state
configuration.
Clock in: Master clock into sensor (48 MHz maximum).
Serial clock: Clock for serial interface.
Global shutter control.
Serial data: Serial data bus, requires 1.5K
Data out: Pixel data output bit 0, D
Pixel clock: Pixel data outputs are valid during falling edge of this
clock. Frequency = master clock.
Strobe: Output is pulsed HIGH to indicate sensor reset operation of
pixel array has completed.
Line valid: Output is pulsed HIGH during line of selectable valid pixel
data (see R0x20 for options).
Frame valid: Output is pulsed HIGH during frame of valid pixel data.
Analog pixel power: Provides power supply for pixel array, 3.3V
±0.3V.
Digital power: Provides power supply for digital block, 3.3V ±0.3V.
Digital ground: Provides isolated ground for digital block.
Analog power: Provides power supply for analog block, 3.3V ±0.3V.
Analog ground: Provides isolated ground for analog block and pixel
array.
No connect: These pins must be left unconnected.
MT9T031: 1/2-Inch 3-Mp Digital Image Sensor
3
Micron Technology, Inc., reserves the right to change products or specifications without notice.
Description
OUT
[9] (MSB), D
Ω
resistor to 3.3V for pull-up.
General Description
©2006 Micron Technology, Inc. All rights reserved.
OUT
OUT
[9:0],
[0] (LSB).