MTCMR-G2-GP-ED Multi-Tech Systems, MTCMR-G2-GP-ED Datasheet - Page 21
![no-image](/images/no-image-200.jpg)
MTCMR-G2-GP-ED
Manufacturer Part Number
MTCMR-G2-GP-ED
Description
MODEM CELLULAR QUAD GPRS
Manufacturer
Multi-Tech Systems
Series
MultiModem® iCellr
Datasheets
1.SF100-G.pdf
(4 pages)
2.MTCMR-E1.pdf
(16 pages)
3.MTCMR-E1.pdf
(79 pages)
4.MTCMR-E1.pdf
(2 pages)
5.MTCMR-E1.pdf
(2 pages)
Specifications of MTCMR-G2-GP-ED
Function
Transceiver, GPRS, Modem
Modulation Or Protocol
GPRS
Frequency
900MHz, 1.8GHz
Applications
General Purpose
Interface
RS-232, USB
Sensitivity
-161dB
Data Rate - Maximum
85.6kbps
Voltage - Supply
9 V ~ 32 V, USB
Package / Case
Module
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
881-1117
Account Activation for Wireless Devices
Please refer to the wireless account Activation Notice included with your unit and located on the MultiModem CD. Follow the
directions on the Activation Notice to activate your account.
Note:
that your wireless network provider has provisioned mobile terminated data and fixed or dynamic public IP address in
which they can configure the network to redirect any incoming connection to that predefined IP.
Verifying Signal Strength
To communicate directly with the cellular modem to verify signal strength, network registration, and roaming status, telnet to the
modem.
Note:
Checking Network Registration and Roaming Status
In this procedure, you will verify that the MultiModem rCell Router has been registered on the wireless network. Using
HyperTerminal, type AT+CREG? for most models. The MTCBA-EV2-EN2 does not support this command, see the Note below
for an alternative method.
Note:
Note:
received signal.
MTCBA-EV2-EN2 Note:
The second from the last response will either be “Modem has registered” or “Modem has NOT registered”.
Multi-Tech Systems, Inc. MultiModem rCell User Guide
Chapter 3 – Carrier Activation
1.
2.
3.
1.
2.
Ensure that the Status LED is blinking, indicating that the router is ready. Ensure that PPP is disabled before verifying
If you need remote access to your MultiModem over the Internet for remote configuration, you need to ensure
Ensure that PPP is disabled before checking network registration and roaming status.
If the router indicates that it is not registered, verify the signal strength to determine if the problem is the strength of the
signal strength.
Click Start I Run icon. In the Open window, enter cmd and then press ENTER.
Click Start I All Programs I Accessories I Command Prompt
●
●
●
To Telnet to the modem. You can access the modem thru the Run icon or from the Command Prompt:
In the command window, type AT+CSQ
The router responds with the received signal strength (rssi) and the channel bit error rate (ber).
In the command window, type AT+CREG?
The router will respond in one of the following ways:
RSSI ranges from 0 to 31. BER ranges from 0 to 7
In the command window, type telnet 192.168.2.1 5000
At the Login prompt, type the default user name: admin (all lower-case). Press ENTER
At the Password prompt, type the default password: admin (all lower-case). Press ENTER
10 – 31
0 – 9
99
Value
+CREG: 0,0
+CREG: 0,1
+CREG: 0,5
Using a terminal program, sending the command AT!STATUS will return several lines of information.
Signal Strength – RSSI
Network Registration Status
The router is not registered on any network
The router is registered on the home network
The router is registered on a network and it is roaming
Sufficient
Weak or Insufficient
Insufficient
Network Registration Verification
or
(7 is the highest error rate).
21