6-6609107-7 TE Connectivity, 6-6609107-7 Datasheet - Page 3
![no-image](/images/manufacturer_photos/0/6/654/te_connectivity_sml.jpg)
6-6609107-7
Manufacturer Part Number
6-6609107-7
Description
Manufacturer
TE Connectivity
Type
EMI/RFI Filteredr
Datasheet
1.5-6609107-4.pdf
(8 pages)
Specifications of 6-6609107-7
Total Number Of Contacts
3POS
Current Rating (max)
6A
Voltage Rating Max
250VAC
Number Of Ports
1Port
Gender
M
Mounting Style
Snap-In
Additional Hardware
Switch/Fuse
Body Orientation
Straight
Operating Temp Range
-10C to 40C
Product Length (mm)
31.49mm
Product Height (mm)
58.67mm
Termination Style
Faston
Lead Free Status / RoHS Status
Compliant
134
P Series
Voltage Selection
The P series of power entry modules provides a dual volt-
age selector which is integrated with the fuseholder. To
simplify the wiring in each individual application, Tyco
Electronics provides dedicated voltage selectors for differ-
ent voltage selection schemes. The two most popular
schemes are the parallel and serial for dual primary trans-
formers and the “DPST switch” for switching mode power
supplies (jumper types.) P series products with an “S” as
the fifth digit are specifically designed for “jumper” type
applications associated with switching mode power sup-
plies. P series products with an “X” as the fifth digit are
specifically designed for dual primary transformer applica-
tions. The voltage selector installed will allow proper wiring
from these applications. No matter what voltage selection
scheme is used, wiring is always made to the same four
terminals.
Shield
A new feature available on the P series is an RF shield. The
metal shield, available on filtered models, provides shield-
ing from radiated emissions and provides an additional RF
ground for the filter to the case. The shield is available in
two versions, a shield of the filter components (designated
by A as the ninth digit) and a complete shield (designated
by B as the ninth digit). The A shield covers the filter por-
tion of the module and increases performance of the filter
by protecting the components from magnetic coupling.
This shield improves RF ground connection to the case
while still allowing the use of the P Series extender. The B
shield covers the entire power entry module with metal,
protecting the equipment from all radiated noise. Used
with the filter, the shield provides the most secure protec-
tion from RFI noise problems. The B shield cannot be used
with any extender.
Catalog 1654001
Revised 05-07
Dimensions are in inches and
millimeters unless otherwise
specified. Values in italics
are metric equivalents.
CORCOM Product Guide
The CHAMELEON Adaptable Module for General, High Performance or
Medical Applications
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
(Continued)
Input Voltage Selection Schemes
X - Dual Primary Transformer Type
S - Jumper Type
Note 1: Jumpers are required if a filter or interconnection module is not
Note 2: Location of optional filter. Jumpers are required if a filter or
Ground
Neutral
Ground
Neutral
Hot
Hot
used.
interconnection block is not used.
USA Cust. Svc.: 1-800-468-2023
CORCOM Prods: 1-847-680-7400
Germany:
A Shield
Note 1
Note 1
Note 1
Note 1
Power on/off
Power on/off
Note 1
Note 1
49-89-6089-0
Note 2
Note 2
G
H
G
H
Provision for
single fusing
Provision for
single fusing
115V
115V
B Shield
www.corcom.com
www.tycoelectronics.com
230V
A
B
C
D
230V
C
A
B
D
Transformer
SMPS
primary
Sel.
Jumpers
Power
input
115V
115V